Fröling GAR 110 Installation And Operating Instructions Manual Download Page 43

Page: 43 / 48

No.

Component

Int.

Operation

Joints

❒

Check that the screws of the clamping plate are
firmly in position and tighten if necessary

❒

Check the joints for wear

➥

Distance between the rotary agitator arms and
cover plate on the open trough must be at least
10 mm

Mitre gear

❒

Carry out a general visual inspection

➥

No major oil leaks should be visible.

Rotary plate

❒

Check the rotary plate for material build-up and
clean if necessary

Trough / dosing screw

❒

Check the trough and dosing screw for dirt and
damage

❒

Check the screw blades for wear

Inlet area / transfer
channel

❒

Check the inlet area for material build-up or jammed
fuel and clean if necessary

❒

Check the shear plate in the entry area of the
transfer trough for wear

Flange bearing

❒

Lubricate bearing at lubricating nipple with grease
gun

Servicing the system

Maintenance work by the operator

Installation and Operating Instructions GAR 110 / 150 | M2060120_en

Summary of Contents for GAR 110

















































Search results

Summary of Contents for GAR 110

Reviews:

Related manuals for GAR 110

Brands by name

Popular brands

Fröling GAR 110, Installation And Operating Instructions Manual

Search results

Summary of Contents for GAR 110

Reviews:

Related manuals for GAR 110

Brands by name

Popular brands