Fröling GAR 110 Installation And Operating Instructions Manual Download Page 28 | Manualshive

Page: 28 / 48

background image

❒

Lubricate shaft stub incl. key with copper paste

❒

Push the geared motor (A) onto the screw end

❒

Secure locking washer (B) with hexagonal screw and washer

If the geared motor cannot be installed as shown above for reasons of space, it is
possible to turn the drive unit:

❒

Fit the torque support with pin on the opposite side

❒

Turn the geared motor and torque support 180° and fit to the screw end and
torque support as explained above

Assembly with screw Ø150

❒

Secure top part of gravity shaft (A) with seal (B) to the closed trough on the boiler
room side

❒

Secure flange plate (C) with seal (D) to top part of gravity shaft

4

Assembly

Assembling the articulated arm rotary agitator

28

Fröling Ges.m.b.H. | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

«
...
26
27
28
29
30
...
»

Summary of Contents for GAR 110

















































Reviews:

No comments

Related manuals for GAR 110

Brand: Rabe Pages: 65

Brand: Navman Pages: 17

Brand: NEILPRYDE Pages: 53

Brand: JAC Pages: 103

Brand: 3Disc Pages: 12

Brand: BACtrack Pages: 13

Brand: Badgematic Pages: 28

Brand: BACtrack Pages: 2

Brand: MADRIX Pages: 28

Brand: BACTcontrol Pages: 28

Brand: EuroLite Pages: 28

Brand: Ultraflex Pages: 3

Brand: Taylor Pages: 41

Brand: ZacUrate Pages: 2

Brand: ZacUrate Pages: 2

VIMCO Sivoia SV-CCI-GRP

Brand: Lutron Electronics Pages: 2

Wallach UltraFreeze

Brand: Cooper Surgical Pages: 4

Monolith NT.115

Brand: Nano Temper Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands