manualshive.com logo in svg

Fresenius Medical Care 5008, Operating Instructions Manual

Share
Download
Fresenius Medical Care 5008 Operating Instructions Manual Download Page 254

Chapter 11:  System Description

11-44

Fresenius Medical Care 5008 OP 5/09.06

Power cable

If the power cable needs to be replaced, use only the original power 
cable listed in the spare parts catalog.

Electromagnetic radiation

Do not use devices emitting electromagnetic radiation, e.g. walkie-
talkies, portable phones, radio transmitters, in the vicinity of dialysis 
systems in operation. This may cause a malfunction of the dialysis 
system.

Batteries

Maintenance of the built-in batteries:

Upon receipt of the system, charge the battery as follows:
– Use the power cable to connect the system to the electrical power 

source.

– Actuate the power switch to turn the system on.
– Leave the system on for 10 hours.

If the system is not used, repeat this procedure every six months.

11.7.3 Water Supply

Purified water quality

Only water which is suitable for dialysis should be used for operating the 
dialysis system. The quality of the water should comply with the local 
regulations (e.g. European Pharmacopoeia - 4

th 

Edition – ISO 

13959:2002). 

Specifications

The ranges of the water inlet pressure, the supply pressure of the 
dialysate concentrate, the temperature, and the flow rates, which are 
required for operating the hemodialysis system, are listed in the chapter 
Specifications.

Installation

The national regulations with regard to the prevention of backflow into 
the water supply system and the air gap between drain connection and 
sewage connection must be observed when installing and operating the 
machine (e.g. in Germany VDE 0753, part 4). For further information 
refer to the Specifications.
Each system must be provided with its own free fall air gap.

3. When determining the room design, a group 1 room is sufficient, i.e., 

the power may be turned off in case of a single fault condition, and 
the treatment may be aborted or repeated.
Additionally, the room must comprise a potential equalization. For 
further information refer to the national regulations (e.g. in Germany 
DIN VDE 0100-710).

Summary of Contents for 5008









































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands