manualshive.com logo in svg

Freescale Semiconductor MCF5329, Reference Manual, Page: 585 / 924

Share
Download
Freescale Semiconductor MCF5329 Reference Manual Download Page 585

FlexCAN

Freescale Semiconductor

23-21

NOTE

The first and last steps are mandatory.

The first write to the control/status word is important in case there was pending reception or transmission. 
The write operation immediately deactivates the MB, removing it from any currently ongoing arbitration 
or ID matching processes, giving time for the CPU to program the rest of the MB (see 

Section 23.3.15.2, 

“Message Buffer Deactivation”

). After the MB is activated in the fourth step, it participates in the 

arbitration process and eventually be transmitted according to its priority. At the end of the successful 
transmission, the value of the free running timer (TIMER) is written into the message buffer’s time stamp 
field, the code field in the control and status word is updated, a status flag is set in the IFLAG register, and 
an interrupt is generated if allowed by the corresponding IMASK register bit. The new code field after 
transmission depends on the code that was used to activate the MB in step four (see 

Table 23-13

).

23.3.12 Arbitration Process

The arbitration process is an algorithm executed by the message buffer management (MBM) that scans the 
entire MB memory looking for the highest priority message to be transmitted. All MBs programmed as 
transmit buffers are scanned to find the lowest ID or the lowest MB number, depending on the 
CANCTRL[LBUF] bit. 

NOTE

If CANCTRL[LBUF] is cleared, the arbitration considers not only the ID, 
but also the RTR and IDE bits placed inside the ID at the same positions they 
are transmitted in the CAN frame.

The arbitration process is triggered in the following events:

•

During the CRC field of the CAN frame

•

During the error delimiter field of the CAN frame

•

During intermission, if the winner MB defined in a previous arbitration was deactivated, or if there 
was no MB to transmit, but the CPU wrote to the C/S word of any MB after the previous arbitration 
finished

•

When MBM is in idle or bus off state and the CPU writes to the C/S word of any MB

•

Upon leaving freeze mode

After the highest priority MB is selected, it is transferred to a temporary storage space called serial 
message buffer (SMB), which has the same structure as a normal MB but is not user accessible. This 
operation is called move-out. At the first opportunity window on the CAN bus, the message on the SMB 
is transmitted according to the CAN protocol rules. FlexCAN transmits up to 8 data bytes, even if the data 
length code (DLC) value is bigger. Refer to 

Section 23.3.15.1, “Serial Message Buffers (SMBs),”

 for more 

information on serial message buffers. 

23.3.13 Receive Process

The CPU prepares or changes an MB for frame reception by writing the following:

1. Control/status word to hold Rx MB inactive (CODE = 0000)

MCF5329 Reference Manual, Rev 3

Summary of Contents for MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments