manualshive.com logo in svg

Freescale Semiconductor MCF5329, Reference Manual, Page: 476 / 924

Share
Download
Freescale Semiconductor MCF5329 Reference Manual Download Page 476

Universal Serial Bus Interface – On-The-Go Module

21-34

Freescale Semiconductor

7

SUSP

Suspend
0 Port not in suspend state.
1 Port in suspend state.
Host mode (USB host and USB OTG):

The PE and SUSP bits define the port state as follows:

When in suspend state, downstream propagation of data is blocked on this port, except for port reset. The 
blocking occurs at the end of the current transaction if a transaction was in progress when this bit was set. In the 
suspend state, the port is sensitive to resume detection. The bit status does not change until the port is 
suspended and there may be a delay in suspending a port if there is a transaction currently in progress on the 
USB.
The module unconditionally clears this bit when software clears the FPR bit. The host controller ignores clearing 
this bit. If host software sets this bit when the port is not enabled (PE = 0), the results are undefined.

This field is cleared if the PP bit is cleared in host mode.

Device mode (USB OTG only):

In device mode, this bit is a read-only status bit.

6

FPR

Force Port Resume. This bit is not-EHCI compatible.
0 No resume (K-state) detected/driven on port.
1 Resume detected/driven on port. 
Host mode (USB host and USB OTG):

Software sets this bit to drive resume signaling. The controller sets this bit if a J-to-K transition is detected while 
the port is in suspend state (PE = SUSP = 1), which in turn sets the USBSTS[PCI] bit. This bit automatically 
clears after the resume sequence is complete. This behavior is different from EHCI where the host controller 
driver is required to clear this bit after the resume duration is timed in the driver.
When the controller owns the port, the resume sequence follows the defined sequence documented in the USB 
Specification Revision 2.0. The resume signaling (full-speed K) is driven on the port as long as this bit remains 
set. This bit remains set until the port switches to the high-speed idle. Clearing this bit has no affect because the 
port controller times the resume operation to clear the bit the port control state switches to HS or FS idle.
This field is cleared if the PP bit is cleared in host mode.

Device mode (USB OTG only):

After the device is in suspend state for 5 ms or more, software must set this bit to drive resume signaling before 
clearing. The device controller sets this bit if a J-to-K transition is detected while port is in suspend state, which 
in turn sets the USBSTS[PCI] bit. The bit is cleared when the device returns to normal operation.

5

OCC

Over-current change. Indicates a change to the OCA bit. Software clears this bit by writing a 1. For host mode, the 
user can provide over-current detection to the USBn_PWRFAULT signal for this condition. For device-only 
implementations (USB OTG only), this bit must always be cleared.
0 No over-current.
1 Over-current detect.

4

OCA

Over-current active. This bit automatically transitions from 1 to 0 when the over-current condition is removed. For 
host/OTG implementations, the user can provide over-current detection to the USBn_PWRFAULT signal for this 
condition. For device-only implementations (USB OTG only), this bit must always be cleared.
0 Port not in over-current condition.
1 Port currently in over-current condition.

Table 21-31. PORTSC1 Field Descriptions (continued)

Field

Description

PE

SUSP

Port State

0

x

Disable

1

0

Enable

1

1

Suspend

MCF5329 Reference Manual, Rev 3

Summary of Contents for MCF5329





























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments