Franklin Electric SUBMONITOR CONNECT MT1111, Installation And Operation Manual

Page: 44 / 232

COMMUNICATIONS
Modbus RTU Communication
44
413 RW N Over Cur Level 100 to 200; default = 110 Over current level percentage. Percent of motor FLA/
SFA. If any phase current is greater than setting for Over
Current Delay, SMC faults/alarms.
414 RW N Over Cur Delay 1 to 120; default = 30 Over current delay, in seconds, to trip fault/alarm. Timer
is reset if the current drops below the motor Over Current
Level.
415 RW N Over Cur Reset 0 - Manual
1 - Automatic (default)
Over current reset method
416 RW N Over Cur Retry 1 to 10; default = 3 Over current automatic reset attempts
417 RW N Over Cur Reset
Delay
1 to 43,200; default = 900 Over current automatic reset delay time
418 RW N Unbl Cur Enable 0 - Off
1 - Fault and Alarm (default)
2 - Alarm Only
Current unbalance protection enable
419 RW N Unbl Cur Level 1 to 50; default = 5 Current unbalance level percentage
420 RW N Unbl Cur Delay 1 to 120; default = 10 Current unbalance delay to trip fault/alarm in seconds
421 RW N Unbl Cur Reset 0 - Manual
1 - Automatic (default)
Current Unbalance Reset Method
422 RW N Unbl Cur Retry 1 to 10; default = 3 Current unbalance automatic reset attempts
423 RW N Unbl Cur Rst Dly 1 to 43,200; default = 900 Current unbalance automatic reset delay in seconds
424 RW N Grnd Flt Enable 0 - Off
1 - Fault and Alarm (default)
2 - Alarm Only
Ground Fault Protection Enable
425 RW N Grnd Flt Level 1.0 to 10.0; default = 1.0
multi = 0.1
Ground Fault Level in amperes
426 RW N No Cur Enable 0 - Off (default)
1 - Fault and Alarm
2 - Alarm Only
No Current Protection Enable
427 RW N Unexp Cur Enable 0 - Off (default)
1 - Fault and Alarm (default)
2 - Alarm Only
Unexpected Current Protection Enable
428 RW N Out Cal Enable 0 - Off (default)
1 - Fault and Alarm (default)
2 - Alarm Only
Out of Calibration Protection Enable
429 RW N Max Str Enable 0 - Off (default)
1 - Fault and Alarm (default)
2 - Alarm Only
Maximum Start Time Protection Enable
430
431
RW N Nominal Voltage 120.0 to 72,000; default =
208.0 multi = 0.1
Nominal Voltage setting
432 RW N Ovr Vlt Enable 0 - Off
1 - Fault and Alarm (default)
2 - Alarm Only
Overvoltage Protection Enable
433 RW N Ovr Vlt Level 101 to 125; default = 110 Overvoltage Level Percentage
434 RW N Ovr Vlt Delay 1 to 120; default = 10 Overvoltage Delay Time in seconds
435 RW N Ovr Vlt Reset 0 - Manual
1 - Automatic (default)
Overvoltage Reset Method
436 RW N Ovr Vlt Retry 1 to 10; default = 3 Overvoltage Automatic Reset Allowed Attempts
437 RW N Ovr Vlt Rst Dly 1 to 43,200; default = 900 Overvoltage Automatic Reset Delay in seconds
Mod
Bus R/W
RC Address Name Choices/Range Description