Förster-Technik TAP5-VS2-50 Original Service Manual Download Page 13

Page: 13 / 130

Introduction

1.3.6

Milk powder container

The milk power container with attachment holds approximately 35 kg of milk substitute.

1.3.7

Number of feeding stations and animals

1.4

Disposal

All components, liquids and solids must be disposed of in compliance with the applicable official
regulations for proper waste recycling and disposal in your country. Also comply with the corre-
sponding safety data sheets.

1.5

Symbols

1.6

Abbreviations

Feeding stations:

max. 4

Calves per feeding station max. 30
Calves per device

max. 120

Optional: A white plus sign on a black background indicates that optional functions or
equipment are being described.

Abbreviation

Meaning

Call ltr. t. or Call t.

Call-off today in liters

Call ltr. y. or Call y.

Call-off yesterday in liters

abs.

absolute

Adli

Ad lib

save amt.

Amount saved up

feed.pump

Feeding pump

out. pause

Dispensing pause

sw.off del.

Switch-off delay

dr. time

Drink-out time

Boiler

dos.

Dosage

Electrode

electrol.

Electrolyte

sw. on del.

Switch-on delay

40 FIT feeding

40 FIT periods

gradient

Gradient control

gr. A (B)

Group A (B)

IFS TR

Intelligent feeding station feed

IFS-4

Intelligent feeding station feed, quadruple unit

Summary of Contents for TAP5-VS2-50



































































































































Search results

Summary of Contents for TAP5-VS2-50

Reviews:

Related manuals for TAP5-VS2-50

Brands by name

Popular brands

Förster-Technik TAP5-VS2-50, Original Service Manual

Search results

Summary of Contents for TAP5-VS2-50

Reviews:

Related manuals for TAP5-VS2-50

Brands by name

Popular brands