Förster-Technik TAP5-VS2-50 Original Service Manual Download Page 117

Page: 117 / 130

Appendix

117

CalfProtect

(open after xx min).

Calibration

OK?

Boiler water

Additive 1/2

Flushing agent

Concentrate stations

Hose pumps

Settings for automatic calibration of MP/water.

Settings for automatic calibration of the hose pump.

Registration

OK?

Antenna test

Set the scheme for the transmitter number assignment: consecutive, automatic.

Reading transmitter numbers.

Set registration mode: no, automatic, available transmitter numbers.

Plans

OK?

Feed:

Feeding plans

Concentrate plans

Quantity limitation: check minimum saved amount/maximum saved amount.

Check the maximum speed of the hose pumps and adjust them if necessary.

Weaning

Concentrate:

Concentrate plan

Portion size

Quantity limitation: check minimum saved amount/maximum saved amount.

Activate accustoming quantity yes/no.

Check amount/threshold and adjust if necessary.

Activate carryover: yes/no

Summary of Contents for TAP5-VS2-50



































































































































Search results

Summary of Contents for TAP5-VS2-50

Reviews:

Related manuals for TAP5-VS2-50

Brands by name

Popular brands

Förster-Technik TAP5-VS2-50, Original Service Manual

Search results

Summary of Contents for TAP5-VS2-50

Reviews:

Related manuals for TAP5-VS2-50

Brands by name

Popular brands