Flavor Burst TS 44BEV User Manual Download Page 14

Page: 14 / 100

Syrup Pump and Related Parts (See Figure 4)

ITEM PART NO.

DESCRIPTION

QTY.

FUNCTION

N/A

SHAKE SYRUP PUMP

Pumps syrup from flavor bags to flavor
lines.

SYR 926

PERISTALTIC SYRUP PUMP

EACH

Pumps syrup from flavor bags into flavor
lines.

TUB 809

1/4" SYRUP SHAKE PUMP
REPLACEMENT TUBE

EACH

Transports syrup through pump.

FIX 1045

1/4" TUBE TO 1/4" HOSE STEM

EACH

Creates tension for tighter fit, connects
pump to fitment.

FIX 1035

1/4 TO 3/16 OD REDUCING UNION

EACH

Connects syrup pump to flavor line out.

FIX 1036

1/4" TO 1/4" OD UNION ELBOW

EACH

Connects bag connector assembly to flavor
line/pump.

SYR 944SH

SYRUP TUBE ASSEMBLY

–

SHAKE BAG COUPLER

Transports the flavoring from the syrup bag
to the syrup pump.

SYR 928

#27-1102-99 .265" BAG COUPLER

EACH

Fastens bag fitment to bag connector.

2B TUB 811

TUBE-SILICONE .188X.375 PE
FB80

EACH

Provides sealed cavity inside bag fitment.

FIX 1048

FITTING ¼ X ¼ BARB FB80

EACH

Connects bag coupler assembly to flavor
line/pump.

SYR 902

FLAVOR-IN TUBE

EACH

Carries syrup from syrup bag to pump.

FAS 2051

ROLLED FLANGE EYELET

Creates tension for tighter fit, 9 per Tube
Assembly.

MIS 3023

DUST CAP

Cover to protect end of flavor lines.

CAB 113

FLAVORING TRAY

Houses syrup bags.

ELE 496TS

PUMP & SANITIZER CABLE
HARNESS

Supplies power from microprocessor to
pump.

SYR 900

4' 9-TUBE ASSEMBLY TUBES

Brings syrup from pump to Blending Head.

ROT 511

LINE COUPLER NUT

Connects flavor lines to the internal 9-Tube
Assembly.

ROT 512

TUBE CONNECTOR BODY

Connects internal 9-Tube Assembly to
flavor lines.

ROT 510

LINE COUPLER

Holds flavor lines in place.

Summary of Contents for TS 44BEV





































































































Search results

Summary of Contents for TS 44BEV

Reviews:

Related manuals for TS 44BEV

Brands by name

Popular brands

Flavor Burst TS 44BEV, User Manual

Search results

Summary of Contents for TS 44BEV

Reviews:

Related manuals for TS 44BEV

Brands by name

Popular brands