Flavor Burst TS 44BEV User Manual Download Page 45

Page: 45 / 100

Winterizing the Unit

If you will not be using your Flavor Burst

system during the off-season or other extended
periods of time, you should winterize the
TS 44BEV system as a precautionary practice
to avoid damage or undesirable syrup build-up
in the unit.

NOTE:

YOU DO NOT NEED TO USE

ANTIFREEZE SOLUTION IN THIS SYSTEM
WHEN WINTERIZING THE UNIT.

1. Perform the entire Clean-In-Place

procedure,

except…

DO NOT perform Step 25 (do not
reconnect the Syrup Bag Connectors to
the syrup bags).

DO NOT perform Steps 33 (do not
assemble or install the Blending
Assembly)

DO NOT perform Step 34 (do not prime
the syrup lines).

2. Place both 9-Tube Assembly lines inside a

container.

3. Remove each syrup bag from its tray and

store as directed on the label.

4. Empty the Sanitizer Tank and return the

tank to the unit.

5. With the Sanitizer Tank empty, press the

INJECTOR FLUSH key until all sanitizer
solution is removed from the sanitizer line.

6. From the Touchscreen main menu, press

the SETUP key in the upper left corner.
Enter the password if required.

7. Press SPOUT A MAINTENANCE (or

SPOUT B MAINTENANCE if the syrup line
dispenses from Spout B).

Summary of Contents for TS 44BEV





































































































Search results

Summary of Contents for TS 44BEV

Reviews:

Related manuals for TS 44BEV

Brands by name

Popular brands

Flavor Burst TS 44BEV, User Manual

Search results

Summary of Contents for TS 44BEV

Reviews:

Related manuals for TS 44BEV

Brands by name

Popular brands