Fidelity Electronics C-10 Series Operation Manual Download Page 62

Page: 62 / 95

Appendix I: - TSC Printer Installation, Setup & Label Upload Procedures

I.1 Get the below ready before Printer Installation

An appropriate cable to connect printer and computer. This cable usually comes with the printer. If not,

contact your printer supplier.

Printer installation driver. This driver usually comes with the printer. If not, contact your printer supplier.

Diagnostic tool for printer. This tool usually comes with the printer. If not, contact your printer supplier or

download it at: -

https://www.fi-measurement.com/files/1/Drivers%20&%20Softwares/DiagTool_V163.zip

TCF file for the label printer. The suitable TCF file can be downloaded at: -

www.fi-measurement.com/resource/driversnsoftwares

I.2 Printer Installation

Turn off the printer, connect the appropriate cable, and then turn on the printer.

If the printer supports Plug-and-Play, and you have connected it using a USB or Parallel cable, then the

Windows Add Hardware Wizard will detect the printer and display a dialog that allows you to install a

driver. Click Cancel and do not install the driver using this wizard.

Run the Driver Wizard utility from the Installation Directory where the driver files are located.

Select Install Printer Drivers and complete the wizard.

The driver should now be installed.

I.3 Uploading TCF File to Printer

In order to allow proper operation between this instrument
and TSC label printer, a TCF file must be uploaded to
printer.

Connect printer with computer.

Power on printer.

Download the correct TCF file point 4 of

I.1

Unzip the download file and save in to

computer.

Run Diagnostic tool for printer.

Click on Command Tool.

Click on Send file.

Double click on the TCF file and it will be

uploaded to printer.

Summary of Contents for C-10 Series
































































































Search results

Summary of Contents for C-10 Series

Reviews:

Related manuals for C-10 Series

Brands by name

Popular brands

Fidelity Electronics C-10 Series, Operation Manual

Search results

Summary of Contents for C-10 Series

Reviews:

Related manuals for C-10 Series

Brands by name

Popular brands