Fidelity Electronics C-10 Series Operation Manual Download Page 14

Page: 14 / 95

3.3 Meaning of Platform No. in this Manual



P1 = the built-in platform of this instrument.



P2 = the external platform connected to this instrument.



PA = P1+P2.

4. Connection Points

4.1 Connection Pins & Plugs

No.

Name

Description

Power Adaptor Input

External  power  adaptor  (DC12V, 1A  center  positive)
is  plugged  in  here.  Do  not  plug  in  any  other  power
adaptor  than  the  one  which  comes  with  this
instrument.

Comport 0 (UART 0 RS232)

Refer to below

4.4

for pin assignment.

Comport 2 (UART 2 RS232)

RS485 and External Input Port

Refer to below

4.3

for pin assignment.

External Platform Input

Load cell cable of P2 is thread through here.
Refer to below

4.2

for pin assignment.

F ~ I

Reserved

Summary of Contents for C-10 Series
































































































Search results

Summary of Contents for C-10 Series

Reviews:

Related manuals for C-10 Series

Brands by name

Popular brands

Fidelity Electronics C-10 Series, Operation Manual

Search results

Summary of Contents for C-10 Series

Reviews:

Related manuals for C-10 Series

Brands by name

Popular brands