Fidelity Electronics C-10 Series Operation Manual Download Page 30

Page: 30 / 95

6. At this point, depends on internal function number F28 setting, instrument may ask for operator

number input. If this is the case: -

•

Input 4-digit operator number, or

•

Press [CE/x10] to skip operator number

7. And press

[Print/M+]

to enter.

8. At this point, instrument is in weighing mode and is ready for operation.

9.3 Operator number

If F28 is set to Yes, instrument will ask for operator number input during power on countdown process.

•

Input operator number: - when prompted, input 4-digit operator number and press

[Print/M+]

. If a

barcode scanner is connected, then simply scan the operator number barcode.

•

To clear operator number: - when prompted, press

[CE/x10]

and press

[Print/M+]

Once an operator number is entered, instrument will transmit the code entered in Lab 1, Lab 3, Lab 4 and Lab
5 output format.

9.4 Warm Up Time

Allow a warm up period of not less than 60 seconds after powered on before using.

9.5 Dual Platform Operation

If external platform is ordered but it is not enabled, contact your dealer for support.

9.5.1 Select preferred weighing platform by [PF/Set]

To enable platform selection through the

[PF/Set]

, set internal function F31 to

P.F.

After that, by pressing

[PF/Set]

, instrument will shift among P1 only, P2 only and both. Platform (s) in operation is indicated by

Indicator.

9.5.2 Summing up transaction results of both platforms

Transaction results of P1 and P2 can be totalized (sum total). To enable platform selection through the

[PF/Set]

set internal function F9 to

•

When only

P1 Indicator

appears = Only P1 is in operation.

•

When only

P2 Indicator

appears = Only P2 is in operation.

•

When both P1 and P2 indicators appear = Both P1 and P2 are in operation and transaction results of
both platforms are totalized and being displayed.

9.6 Keyboard Lock

When keyboard lock is enabled in F20, only

[On/Off]

[Zero]

[Tare]

and

[On/Off]

keys can function during

normal operation.

9.7 Loads and Weighing Platform

•

Always place an object onto platform gently. Excessive force / shock applied to platform may cause un-
recoverable damage to the weight sensor inside platform.

•

It is a good practice to remove all loads from platform after weighing. It will prolong the life of the weight
sensor.

Summary of Contents for C-10 Series
































































































Search results

Summary of Contents for C-10 Series

Reviews:

Related manuals for C-10 Series

Brands by name

Popular brands

Fidelity Electronics C-10 Series, Operation Manual

Search results

Summary of Contents for C-10 Series

Reviews:

Related manuals for C-10 Series

Brands by name

Popular brands