Feig Electronic TST FUZ2-A Assembly Instructions Manual Download Page 62

Page: 62 / 71

TST

Assembly instructions

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 60 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

No.

Description

Possible reason for error

F.921

Internal 15 V voltage incorrect

• Hardware defect

F.922

E-Stop chain not complete

Not all E-STOP inputs are separately jumpered although the entire E-Stop chain is jumpered
• Redundant checking of the E-Stop chain tripped

F.925

Testing of the third shutdown
method failed

• defective hardware

F.928

Faulty input testing

• The testing of an cyclic tested input was not successful
• The connected device is not working
• The cable connection between the connected device and the controller is broken

F.92A

If the motor wiring test is activated
by P.112 the wiring will be tested
during system tests.

• min. one of the motor cables is not good or nor connected
• Motor cable damaged
• Motor damaged

F.930

External watchdog incorrect

• Defective hardware or noise-saturated environment

F.931

ROM error

• Wrong EPROM code
• Defective hardware or noise-saturated environment

F.932

RAM error

• Defective hardware or noise-saturated environment

F.933

Wrong frequency of CPU

• The clock frequency of the processor is wrong

F.935

Stack error

• User-Stack or System-Stack overflowed
• Possible software error due to recursive invocations (e.g. profile)

F.942

RAM Error of I/O Processor

• RAM Error of I/O Processor

F.960

Faulty parameter checksum

• New EPROM version with different parameters
• Controller not yet initialized

F.961

Checksum from calibration values
etc.

• New EPROM version with different EEPROM structure
• Controller not yet initialized

F.962

Converter parameters not
plausible

• New EPROM version
• Controller not yet initialized

F.964

Program version / manufacturer
code

• New EPROM version
• Controller not yet initialized

F.965

Faulty door cycle counter with
active emergency opening

• The door cycle counter does not count or is faulty. Because of this no emergency opening testing can be done.

F.966

Hardware unknown

• A wrong software was programmed to the controller
• The programmed software does not know the hardware version
• The controller hardware is broken

F.968

Programming error with Real time
clock

• The clock is not programmed plausible

F.969

Internal error Real time clock

• The clock has an error → make a reset

F.970

Plausibility parameter block error

• New EPROM version
• Controller not yet initialized
• Some parameter is implausible

Summary of Contents for TST FUZ2-A








































































Search results

Summary of Contents for TST FUZ2-A

Reviews:

Related manuals for TST FUZ2-A

Brands by name

Popular brands

Feig Electronic TST FUZ2-A, Assembly Instructions Manual

Search results

Summary of Contents for TST FUZ2-A

Reviews:

Related manuals for TST FUZ2-A

Brands by name

Popular brands