manualshive.com logo in svg

Feig Electronic TST FUZ2-A, Assembly Instructions Manual, Page: 48 / 71

Share
Download
Feig Electronic TST FUZ2-A Assembly Instructions Manual Download Page 48

TST

 

Assembly instructions

 

FUZ2 -A/-B/-C/-CX/-L 

 

FEIG ELECTRONIC GmbH

 

Page 46 of 71

 

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

 

The subsequent OPENING and CLOSING of the door in 

automatic mode adjusts the pre-limit switches and limit switch 
tapes are taught-in automatically. 

 

 

2. 

Start correction drive by pressing the 

 OPEN-key.

 

! Korrekturfahrt ! 
xxx Start mit 

 

I.515 

Door opens and is taught-in into the position. 

Door  opens. 
I.555 Lern Fahrt 

I.555 

Display in end position OPEN. 

Offenh=    xxs 
I.515 Korr. Fahrt 

I.515 

 
 

 

The door will close automatically after the auto close time has 
count down and moves up and down by itself until the correction 
drive has finished. 
The Display shows the following messages: 

Door closes. 
I.515 Korr. Fahrt 

I.515 

Offenhalt = xxs 
I515 Korrekt. Fahrt 

I.515 

Display that correction was completed. 
 
 
 
 
Optional display during a subsequent correction. 
 
 
 
 
 
The door closes and remains in the end position CLOSE. 

Offenh 1 = xxs 
I.510 Korrek. OK 

T.5 

Offenh 1 = xxs 
Automatik 

T.5 

Door  opens. 

I.515 

`AUF` 

Offenh 1 = xxs 
I 100 Auf Geschw. 

I.100 

Offenh 1 = xxs 

T10 

Door closes. 

2

UF` 

The commissioning of the light curtain has been successfully 
completed. 

FEIG ELECTRONIC 
xxx Zyklen 

_EU_ 

 

 
 

The end position CLOSE must usually be corrected subsequently. This can be performed via the 

following parameters: 
 
221: Correction value end position door CLOSE -> this parameter must be reset after every new teach-in of 
all end positions (P.210=5). 
P.275: Correction of increments after conclusion of the synchronization -> recommended as fine setting for 
the end position BELOW. The value set here must NOT be re-set after the new teach-in of all end positions. 
 

 

 

Summary of Contents for TST FUZ2-A








































































Reviews:

No comments