Feig Electronic TST FUZ2-A Assembly Instructions Manual Download Page 60 | Manualshive

Page: 60 / 71

background image

TST

Assembly instructions

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 58 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

No.

Description

Possible reason for error

F.80B

Wrong Test of input B of the
stationary unit TST FSx

• Input B of the stationary unit was tested wrong
• The device which is connected to the input does not work correct
• The stationary unit is defective

F.80C

Wrong Test of input C of the
stationary unit TST FSx

• Input C of the stationary unit was tested wrong
• The device which is connected to the input does not work correct
• The stationary unit is defective

F.811

Wrong test for output 1 of the
stationary unit

• Output 1 of the stationary unit was tested incorrectly
• The cable between the stationary unit and the controller is damaged or not connected
• The stationary unit is defective
• Incorrect settings for parameter P.5xF, P.47b or P.465

F.812

Wrong Test for output 2 of
stationary unit TST FSx

• Output 2 of the stationary unit was tested incorrectly
• The cable between stationary unit and controller is damaged or not connected
• The stationary unit is defective
• Incorrect settings for parameter P.5xF, P.47b or P.465

F.813

Wrong Test of output 3 of the
stationary unit TST FSx

• Output 3 of the stationary unit was tested incorrectly
• The cable between the stationary unit and the controller is damaged or not connected
• The stationary unit is defective
• Incorrect settings of parameter P.5xF, P.47b or P.465

F.821

Wrong parameter setting input 1 of
mobile unit

• The device which is connected to input 1 of the mobile unit does not fit to the settings
• Check Parameter P.F1F

F.822

Wrong parameter setting input 2 of
mobile unit

• The device which is connected to input 2 of the mobile unit does not fit to the settings
• Check Parameter P.F2F

F.823

Wrong parameter setting input 3 of
mobile unit

• The device which is connected to input 3 of the mobile unit does not fit to the settings
• Check Parameter P.F3F

F.824

Wrong parameter setting input 4 of
mobile unit

• The device which is connected to input 4 of the mobile unit does not fit to the settings
• Check Parameter P.F4F

F.831

Disturbed input 1 of mobile unit
TST FSx

• The input 1 of the mobile unit is disturbed
• The connection to the device is interrupted

F.832

Disturbed input 2 of mobile unit
TST FSx

• The input 2 of the mobile unit is disturbed
• The connection to the device is interrupted

F.833

Disturbed input 3 of mobile unit
TST FSx

• The input 3 of the mobile unit is disturbed
• The connection to the device is interrupted

F.834

Disturbed input 4 of mobile unit
TST FSx

• The input 4 of the mobile unit is disturbed
• The connection to the device is interrupted

F.841

Frequency error on input 1 of
mobile unit

• The connected optical safety edge is faulty

F.843

Frequency error on input 3 of
mobile unit

• The connected optical safety edge is faulty

«
...
58
59
60
61
62
...
»

Summary of Contents for TST FUZ2-A








































































Reviews:

No comments

Related manuals for TST FUZ2-A

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: Vacon Pages: 64

Brand: Rain Bird Pages: 48

Brand: Danfoss Pages: 20

Brand: Danfoss Pages: 36

Brand: Harman Kardon Pages: 25

Brand: Uniss Pages: 21

Brand: Magnescale Pages: 3

Brand: National Instruments Pages: 31

Brand: National Instruments Pages: 24

Brand: National Instruments Pages: 85

Brand: National Instruments Pages: 10

Brand: National Instruments Pages: 16

Brand: National Instruments Pages: 98

CompactRIO cRIO-9002

Brand: National Instruments Pages: 21

Brand: National Instruments Pages: 145

Brand: National Instruments Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands