Feig Electronic TST FUZ2-A Assembly Instructions Manual Download Page 56

Page: 56 / 71

TST

Assembly instructions

FUZ2 -A/-B/-C/-CX/-L

FEIG ELECTRONIC GmbH

Page 54 of 71

FUZ2-A-B-C-CX-L_Montageanleitung_GB

_10.docx

No.

Description

Possible reason for error

F.383

Interruption on safety input

• Connection cable defective or not connected
• Termination resistor incorrect or missing
• Jumper incorrectly set

F.384

Safety input

– testing failed

• Safety edge was not activated as expected when requesting a test.
• The time between request for testing and actual testing not in agreement

F.385

Fault in pre-limit switch for safety
edge

• Pre-limit switch for turning off the safety edge or reversing after safety edge tripping remains tripped even in the
upper end position.

F.386

Too high a pulse frequency for
optical safety edge

• Defective optical safety edge
• Defective input for internal safety edge

F.389

Safety input incorrectly
parameterized

• A safety edge is connected but deactivated
Safety input Jumper incorrectly set (as digital input jumpered but as safety edge set)

F.38A

Redundancy error of the 8K2 slip
door switch on the second internal
safety edge evaluation unit

• One of the contacts of the redundant 8k2 slip door switch is defective
• The slip door was not fully opened or closed

F.3A1

Number of trips for safety input A
has reached set limit

• Parameterized, maximum number of safety input trips during a door cycle was exceeded

F.3B1

Number of trips for safety input B
has reached set limit

• Parameterized, maximum number of safety input trips during a door cycle was exceeded

F.3C1

Number of trips for safety input C
has reached set limit

• Parameterized, maximum number of safety input trips during a door cycle was exceeded

F.400

Controller hardware reset detected

• Excessive noise on supply voltage
• Internal watchdog tripped
• RAM error

F.401

Watchdog Error

• Internal Watchdog has released

F.40A

Software Exeption

• Internal error detected

F.40B

Communication error expansion
board

• The communication between main board and expansion board is disturbed

F.40C

Unknown extension board (CAN
connection)

• Incorrect hardware coding of the extension board
• Control software does not support the expansion card
• Expansion card defective

F.410

Over-current (motor current or DC-
bus)

• Wrong motor data set (P.100 – P.103)
• Non-adjusted voltage increase / boost set
(P.140 or P.145)
• Motor not properly dimensioned for door
• Door sticks

Summary of Contents for TST FUZ2-A








































































Search results

Summary of Contents for TST FUZ2-A

Reviews:

Related manuals for TST FUZ2-A

Brands by name

Popular brands

Feig Electronic TST FUZ2-A, Assembly Instructions Manual

Search results

Summary of Contents for TST FUZ2-A

Reviews:

Related manuals for TST FUZ2-A

Brands by name

Popular brands