11. Switch 11 (SignalMaster
ALTERNATE).
Press switch 11 to activate an alter-
nating flash pattern(four lamps in the center, then
two outer lamps on both sides). The switch 11 LED
illuminates and the row of LED’s under the V-shaped
display simulates the light pattern being executed by
the directional signal. Press switch 11 again to
deactivate the alternating flash pattern and extin-
guish the switch 11 LED.
12. Switch 12 (SignalMaster RIGHT).
Press switch 12 to activate a right
arrow directional signal directing traffic around the
right side of the vehicle. The switch 12 LED illumi-
nates and the row of LED’s under the V-shaped
display simulates the light pattern being executed by
the directional signal. Press switch 12 again to
deactivate the right arrow directional signal and
extinguish the switch 12 LED.
C.
Keyboard Configuration 4 (FIRE A).
NOTE
Refer to figure 1-3 while reading paragraph
1-6.C.
1.
Switch 1 (RESET).
Press this switch to extinguish all
lights (if activated) in the lightbar. The RESET LED
will illuminate and the reflectors rotate to the “home”
position. All other LED’s will extinguish and acti-
vated functions will deactivate.
NOTE
The RESET switch may be pressed at any time
to deactivate any previously selected function(s).
2.
Switch 2 (Blank).
In this keyboard configuration, this
switch is not assigned a function. The installer/
programmer MUST inform you what function (if any)
is assigned to this switch.
Figure 1-3. Keyboard Configuration 4.
3.
Switch 3 (RELAY A).
Press switch 3 to activate the auxiliary
device, such as headlight flashers or grille lights,
connected to the relay A output. The installer should
inform you what device (if any) is connected to the
relay A output. The switch 3 LED will illuminate.
Press switch 3 again to deactivate the auxiliary
device and extinguish the switch 3 LED.
4.
Switch 4 (RELAY B).
Press switch 4 to activate the auxiliary
device connected to the relay B output. The installer
should inform you what device (if any) is connected to
the relay B output. The switch 4 LED will illuminate.
Press switch 4 again to deactivate the auxiliary
device and extinguish the switch 4 LED.
5.
Switch 5 (RELAY C).
Press switch 5 to activate the auxiliary
device connected to the relay C output. The installer
should inform you what device (if any) is connected to
the relay C output. The switch 5 LED will illuminate.
Press switch 5 again to deactivate the auxiliary
device and extinguish the switch 5 LED.
6.
Switch 6 (MODE 1).
Press switch 6 to activate Mode 1. In
this keyboard configuration; the center light oscil-
lates to the front, one light oscillates to the left, and
one light oscillates to the right. The LED’s in the V-
shaped display will flash indicating the lights are
activated and the switch 6 LED will illuminate. Press
switch 6 again to deactivate Mode 1. The LED’s in
the V-shaped display and the switch 6 LED will
extinguish.
7.
Switch 7 (MODE 2).
Press switch 7 to activate Mode 2. In
this keyboard configuration, four lights rotate at 90
FPM and three lights oscillate to the front. The
LED’s in the V-shaped display will flash indicating
the lights are activated and the switch 7 LED will
illuminate. Press switch 7 again to deactivate Mode
2. The LED’s in the V-shaped display and the switch
7 LED will extinguish.
8.
Switch 8 (MODE 3).
Press switch 8 to activate Mode 3. In
this keyboard configuration, all seven lights rotate in
synchronization at 90 FPM creating a center-out
pattern. The LED’s in the V-shaped display will flash
indicating the lights are activated and the switch 8
LED will illuminate. Press switch 8 again to deacti
1-7
RESET
2
3
4
5
6
7
8
9
10
11
12
1 - Reset
2 - No function assigned
3 - Relay A (push-on/push-off)
4 - Relay B (push-on/push-off)
5 - Relay C (push-on/push-off)
6 - Mode 1 (pattern #48)
7 - Mode 2 (pattern #26)
8 - Mode 3 (pattern #27)
9 - V-Bar - Left (pattern #63)
10 - V-Bar - Center Out (pattern #64)
11 - V-Bar - Alternate (pattern #65)
12 - V-Bar - Right (pattern #62)
Summary of Contents for VISION
Page 2: ......
