NOTE
If switch 2 is pressed and held allowing the
activated take-down lights to rotate more
than approximately 1-1/2 revolutions, an error
indication will occur. Press switch 1 (RESET)
to clear the error indication and start over.
3.
Switch 3 (TAKE-DOWN).
Press switch 3 to activate the take-
down lights. The two lights fitted with clear domes
illuminate and rotate to the take-down (straight
ahead) position. Two LED’s in the V-shaped display
(which represent the take-down lights) will illumi-
nate and the switch 3 LED illuminates. Press switch
3 again to deactivate the take-down lights. The
LED’s in the V-shaped display and switch 3 LED will
extinguish. The take-down lights will return to the
previously activated function, if any.
NOTE
Take-down lights can be aimed or rotated hori-
zontally. Refer to the switch operation descrip-
tions JOG LEFT (above) and JOG RIGHT
(below).
4.
Switch 4 (JOG RIGHT).
Press switch 4 to manually position
activated take-down lights for use as a spotlight.
Each time switch 4 is pressed, the activated light will
move one step to the right and the switch 12 LED
will illuminate momentarily. Press and hold switch 4
until the activated light rotates right to the desired
position.
NOTE
If switch 4 is pressed and held allowing the
activated take-down lights to rotate more
than approximately 1-1/2 revolutions, an
error indication will occur. Press switch 1
(RESET) to clear the error indication and
start over.
5.
Switch 5 (RELAY A).
Press switch 5 to activate the auxiliary
device, such as headlight flashers or grille lights,
connected to the relay A output. The installer should
inform you what device (if any) is connected to the
relay A output. The switch 5 LED will illuminate.
Press switch 5 again to deactivate the auxiliary
device and extinguish the switch 5 LED.
6.
Switch 6 (MODE 1).
Press switch 6 to activate Mode 1. In
this keyboard configuration; a four-light, alternating,
oscillating pattern to the rear is activated. The LED’s
in the V-shaped display will flash indicating the
lights are activated and the switch 6 LED illumi-
nates. Press switch 6 again to deactivate Mode 1. The
LED’s in the V-shaped display and the switch 6 LED
will extinguish.
7.
Switch 7 (MODE 2).
Press switch 7 to activate Mode 2. In
this keyboard configuration, four lights rotate at 90
FPM and three lights oscillate to the front. Also, the
auxiliary devices (if any) connected to the relay B and
C outputs will activate. The installer should inform
you what devices (if any) are connected to the relay B
and C outputs. The LED’s in the V-shaped display
will flash indicating the lights are activated and the
switch 7 LED will illuminate. Press switch 7 again to
deactivate Mode 2. The LED’s in the V-shaped
display and the switch 7 LED will extinguish.
8.
Switch 8 (MODE 3).
Press switch 8 to activate Mode 3. In
this keyboard configuration, all seven lights rotate in
synchronization at 90 FPM creating a center-out
pattern. The LED’s in the V-shaped display will flash
indicating the lights are activated and the switch 8
LED will illuminate. Press switch 8 again to deacti-
vate Mode 3. The LED’s in the V-shaped display and
the switch 8 LED will extinguish.
9.
Switch 9 (SignalMaster LEFT).
Press switch 9 to activate a left arrow
directional signal directing traffic around the left side
of the vehicle. The switch 9 LED illuminates and the
row of LED’s under the V-shaped display simulates
the light pattern being executed by the directional
signal. Press switch 9 again to deactivate the left
arrow directional signal and extinguish the switch 9
LED.
10. Switch 10 (SignalMaster CENTER
OUT).
Press switch 10 to activate a center out
directional signal directing traffic around both sides
of the vehicle. The switch 10 LED illuminates and
the row of LED’s under the V-shaped display simu-
lates the light pattern being executed by the direc-
tional signal. Press switch 10 again to deactivate the
center out directional signal and extinguish the
switch 10 LED.
1-6
Summary of Contents for VISION
Page 2: ......
