Farymann Diesel 15B Series Operator'S Manual Download Page 89

Page: 89 / 110

Diesel engine Series 15B / 18B

Faults

2008-09-08

Pos: 9.12 /KN2006-SM/Störungen/005 1.1 Störungstabelle_Titel @ 9\mod_1144442349705_2.doc @ 87248

9.2 Troubleshooting

chart

Pos: 9.13 /KN2006-Projekte/Bukh-Farymann/Störungen/005 1.1.0 Störungstabelle 43F @ 45\mod_1188130353128_2.doc @ 570577

9.2.1 Engine does not start

Error

Possible cause

Troubleshooting

Clearance by

No fuel in the tank

Filling with fuel

Operator

Speed adjusting lever is in the
Stop position

Put speed adjusting lever in the
"full load" position

Operator

Ventilation in the fuel filler cap
blocked

Replace fuel filler cap

Operator

Fuel line interrupted

Check fuel lines

Operator

If the injection
noise (chattering)
cannot be heard

Fuel filter blocked

Replace fuel filter

Operator

Fuel line broken or leaky
connection

Replace fuel line or tighten
connection

Operator

Vapour bubble formation caused
by too hot fuel

Let fuel cool down

Operator

Paraffin precipitation in the fuel
(for low external temperature
approx. -10 °C)

Drain and flush fuel system,
replace fuel filter, use winter fuel

Skilled
employee

Failure of the fuel
system; turn
engine by hand
and pay attention
to the typical
"chatter" of the
injection nozzle.

Defective injection nozzle

Check injection nozzle, replace if
necessary

Skilled
employee

Petrol instead of diesel in the tank Drain tank and fuel system and

arrange for engine to be checked
by a Greaves Farymann Diesel
service partner (petrol in the tank
results in engine damage)

Skilled
employee

If the injection
noise (chattering)
can be heard

Air intake tract blocked

Check intake area of the air filter
case and air filter cartridge

Operator

Incorrect valve clearance

Adjust valve clearance

Skilled
employee

Decompression unit defective

Check decompression unit,
replace if necessary

Skilled
employee

Leaky valves

Check valves, repair or replace

Skilled
employee

Compression too
low

Leaky cylinder head / cylinder
head gasket

Replace cylinder head gasket

Skilled
employee

Summary of Contents for 15B Series















































































































Search results

Summary of Contents for 15B Series

Reviews:

Farymann Diesel 15B Series, Operator'S Manual, Page: 89 / 110

Search results

Summary of Contents for 15B Series

Reviews: