manualshive.com logo in svg

Farymann Diesel 15B Series, Operator'S Manual, Page: 15 / 110

Share
Download
Farymann Diesel 15B Series Operator'S Manual Download Page 15

 

Diesel engine Series 15B / 18B 

 

Safety 

 

 

2008-09-08

  

15 

 

Pos: 2.25 /KN2006-SM/Sicherheit/007 Besondere Gefahren/007 1.1 Besondere Gefahren_Titel und Einleitung @ 8\mod_1143366409048_2.doc @ 81172 

 

2.5 Specific 

dangers 

The following section lists the residual risks that have been 
determined by the risk assessment. 

„

 

Heed the safety instructions listed here, and the warnings in 
subsequent chapters of this Manual, to reduce health hazards 
and to avoid dangerous situations. 

Pos: 2.26 /KN2006-SM/nL---------- Abschnittsende ---------- @ 8\mod_1141997892953_0.doc @ 75473 

 

 

Pos: 2.27 /KN2006-Projekte/Bukh-Farymann/Sicherheit/Rotierende Bauteile 43F (P02032) @ 31\mod_1172219618482_2.doc @ 358635 

 

Rotating parts 

 

 

WARNING! 
Risk of injury due to rotating parts 

Rotating parts can cause severe injuries. 

Therefore: 

–  Do not reach into or work on rotating parts 

during operation. 

–  Do not open or remove covers during operation. 

–  Pay attention to the run-on time after switching 

off the engine. 
Ensure there are no parts still moving or the 
engine is not running before opening the 
covers. 

–  Wear close-fitting work clothing. 

 

  

Pos: 2.28 /KN2006-SM/nL---------- Abschnittsende ---------- @ 8\mod_1141997892953_0.doc @ 75473 

 

 

Summary of Contents for 15B Series















































































































Reviews:

No comments