manualshive.com logo in svg

Farymann Diesel 15B Series, Operator'S Manual, Page: 33 / 110

Share
Download
Farymann Diesel 15B Series Operator'S Manual Download Page 33

 

Diesel engine Series 15B / 18B 

 

Transport, packing and storage 

 

 

2008-09-08

  

33 

 

Pos: 5.1 /KN2006-SM/Transport, Verpackung und Lagerung/001 1 Transport, Verpackung und Lagerung_Titel @ 9\mod_1144048567385_2.doc @ 84504 

 

5  Transport, packing and storage 

Pos: 5.2 /KN2006-SM/Transport, Verpackung und Lagerung/002 1.1 Sicherheitshinweise für den Transport_Titel @ 9\mod_1144048644190_2.doc @ 84511 

 

5.1  Safety notes for transport 

Pos: 5.3 /KN2006-Projekte/Bukh-Farymann/Transport, Verpackung und Lagerung/Unsachgemäßer Transport @ 48\mod_1191325180893_2.doc @ 636977 

 

Improper transport 

 

 

CAUTION! 
Damage due to improper transport! 

Significant damage to property and injuries to 
persons can occur in the case of improper 
transport. 

Therefore: 

–  Proceed carefully when unloading the packages 

and on delivery and internal transport and 
observe the signs and notices on the packing. 

–  Only use the attachment points provided. 

–  Do not remove packing until just before the 

installation. 

 

 

 

Pos: 5.4 /KN2006-SM/nL---------- Abschnittsende ---------- @ 8\mod_1141997892953_0.doc @ 75473 

 

 

Pos: 5.5 /KN2006-SM/Transport, Verpackung und Lagerung/004 1.1 Transportinspektion_Titel @ 9\mod_1144054094956_2.doc @ 84694 

 

5.2 Transport 

inspection 

Pos: 5.6 /KN2006-SM/Transport, Verpackung und Lagerung/004 1.1.0 Transportinspektion - Inhalt, Kurzform @ 9\mod_1144054141858_2.doc @ 84751 

 

Check the delivery immediately on receipt for completeness and 
transport damage. 

If externally detectable transport damage is found, proceed as 
follows: 

„

  Do not accept the delivery, or only with reservation. 

„

  Record the extent of transport damage in the transport 

documents or on the delivery note of the forwarding agent.  

„

  Start complaints procedure. 

 

 

NOTE! 

Claim any damage as soon as it is detected. 
Compensation claims can only be submitted within 
the applicable complaints periods. 

 

Pos: 5.7 /KN2006-SM/nL---------- Abschnittsende ---------- @ 8\mod_1141997892953_0.doc @ 75473 

 

 

Summary of Contents for 15B Series















































































































Reviews:

No comments