manualshive.com logo in svg

Farymann Diesel 15B Series, Operator'S Manual

Share
Download
Farymann Diesel 15B Series Operator'S Manual Download Page 43

 

Diesel engine Series 15B / 18B 

 

Installation and commissioning 

 

 

2008-09-08

  

43 

 

 

Pos: 6.13 /KN2006-Projekte/Bukh-Farymann/Installation und Inbetriebnahme/1.1 

Kraftstoff auffüllen 6415 @ 54\mod_1196690296374_2.doc @ 836484 

 

6.5 Filling 

with 

fuel 

     

 

CAUTION! 
Engine damage due to contaminated fuel! 

The injection system and the engine can be 
damaged by dirt particles or other contamination in 
the fuel. 

Therefore: 

–  Only fill with clean diesel fuel according to EN 

5090, DIN 590. 

–  Pay attention to cleanliness so that no dirt gets 

into the fuel tank. 

–  The engine must stand up straight for filling with 

fuel. 

 

 

 

 

NOTE! 

Use winter diesel fuel for temperatures below 0 °C. 

The fuel filler cap (Fig. 22/1) has a vent. Do not 
make any modifications or use a non-original fuel 
filler cap. Otherwise, optimum fuel supply is not 
guaranteed. 

Fill the tank to the maximum before first use or 
after the fuel system runs empty. In this way, the 
venting of the fuel system is performed 
automatically (self-venting fuel system). 

 

 

6.5.1  Filling process 4.0 litre tank (option) 

 

 

Fig. 22 

1. 

Open the fuel filler cap (1) by turning it anticlockwise. 

 

Summary of Contents for 15B Series















































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands