manualshive.com logo in svg

Farymann Diesel 15B Series, Operator'S Manual, Page: 70 / 110

Share
Download
Farymann Diesel 15B Series Operator'S Manual Download Page 70

 

Diesel engine Series 15B / 18B 

Maintenance 

 

 

 

70  

2008-09-08

 

 

 

Fig. 47 

8. 

Release oil filler cap (3) e.g. with a jaw spanner SW 13 and 
screw off by hand. 

9. 

Fill with engine oil. 

10.  Only tighten the oil filler cap (3) by hand (risk of breakage). 

11.  Start engine and check for leaks. 

 

 

NOTE! 

Always replace engine oil and oil filter together. 

 

 

 

Pos: 8.22 /KN2006-SM/nL---------- Abschnittsende ---------- @ 8\mod_1141997892953_0.doc @ 75473 

 

 

Pos: 8.23 /KN2006-Projekte/Bukh-Farymann/Wartung/1.1 

Ölfilter wechseln 6415 @ 54\mod_1196766864335_2.doc @ 873838 

 

8.7  Replacing oil filter 

 

 

Fig. 48 

1. 

Slacken oil filter (3) with an oil filter wrench (1) and e.g. a ring 
spanner SW 27 (2), and unscrew and remove afterwards by 
hand. 

 

 

NOTE! 

The oil filter can be "hot". 

 

 

 

 

Fig. 49 

2. 

Collect the engine oil from the oil filter (4) and oil filter case in 
a suitable container (5) and dispose of in accordance with the 
environmental regulations. 

Summary of Contents for 15B Series















































































































Reviews:

No comments