Farfisa AD2121CAG series Technical Manual Download Page 59

Page: 59 / 208

(MT13 - En 2015)

Direct connection to external stations; to enable this service set
the button with the address of the external station (codes from 231 to
250). Follow the programming procedure “2” described on page
2.49.

Various services through actuators art.2281; to enable this

service set the button with the address of the actuator to be enabled
(codes from 211 to 220). Follow the programming procedure “2”
described on page 2.49.

1) Function buttons for intercom calls in the same apartment

For this function only the internal address must be set, as the user
address is the same set during the user address programming procedure
described on page 2.47.
To program the internal address and it is necessary to:

enter the programming mode following the instructions described
in “Enter the programming phase”;

a - keep pressed for more than 4 seconds the button you wish to
program; the programming tone will be heard;
b - keep pressed the button "

" for more than 4 seconds; the

programming tone will be heard;
c - enter the 3 digit of the address (codes from 000 to 007) following
the procedure reported on the paragraph “Entering codes or
addresses”;
d - press the button

to confirm; the acknowledge tone will be

heard;
repeat phases a-b-c-d to program other buttons or exit the program-
ming mode by hanging up the handset; the acknowledge tone will be
heard.

2) Function buttons for calls to other users, external stations

or actuators

Note. Intercom conversations or connections with users and external
stations of other buildings will not be possible if digital exchanger
art.2273 is installed.
For this function only the user address must be set as the internal
address is irrelevant.
To program the user address and it is necessary to:

enter the programming mode following the instructions described
in “Enter the programming phase”;

a - keep pressed for more than 4 seconds the button you wish to
program; the programming tone will be heard;
b - enter the 3 digit of the address (codes from 001 to 250) following
the procedure reported on the paragraph “Entering codes or
addresses”;
c - press the button

to confirm; the acknowledge tone will be

heard;
repeat phases a-b-c to program other buttons or exit the program-
ming mode by hanging up the handset; the acknowledge tone will be
heard.

Resetting the default programming values

To reset the intercom default programming values and delete all the
variations made in the programming mode you must:

enter the programming mode following the instructions described
in “Enter the programming phase”;
enter the 3 digit 123 following the procedure reported on the paragraph
“Entering codes or addresses”; the tone indicates that the default
values have been restored;
exit the programming phase by hanging up the handset.

Choosing the type of ringer for all calls

The intercom can receive 4 different calls that can be changed as
indicated in the procedure below. The default programming values and
the call sequence are shown in table 2.11 of page 2.47.
All programming operations must be carried out with the handset
in idle position.

INTERNAL STATIONS

Call from external door station

Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone that was programmed for calls from external door station.
Press the button "

" repeatedly to select the ring tone.

Press the button

to confirm; the acknowledge tone will be heard.

Intercommunicating call

Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone of calls from external door station.
Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone that was programmed for intercommunicating calls.
Press the button "

" repeatedly to select the ring tone.

Press the button

to confirm; the acknowledge tone will be heard.

Call from other user

Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone of calls from external door station.
Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone of intercommunicating calls.
Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone that was programmed for calls from other user.
Press the button "

" repeatedly to select the ring tone.

Press the button

to confirm; the acknowledge tone will be heard.

Floor (local) call

Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone of calls from external door station.
Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone of intercommunicating calls.

Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone that was programmed for floor call.
Press the button "

" repeatedly to select the ring tone.

Press the button

to confirm; the acknowledge tone will be heard.

Duration of ringers

By default, all the intercom calls last for 4 rings, with the only exception
of the floor call consisting of only one ring that cannot be changed. The
number of rings can be varied by leaving the receiver in its seat and
proceeding as follows:

Keep pressed the button "

" for more than 4 seconds; you hear the

ring tone of calls from external door station.
Press the button “

” for 4 seconds, it will be possible to listen to a

number of beeps corresponding to the rings programmed.
Repeatedly press the “

” button to select the desired number of rings.

Each pressure increases the duration of the ringing time by one ring.
After 8 rings it again starts from 1.
Press the button

to confirm; the acknowledge tone will be heard.

Adjusting the volume of the ring tone

With the handset in idle position, you can adjust 5 volume levels for all
ring tones, as indicated below:

Keep pressed the button "

" for more than 4 seconds; you hear the