2.
42
(MT13 - En 2015)
- Intercom conversations or connections with
users and external stations of other buildings
will not be possible if digital exchanger art.2273
is installed.
- A programming example is on page 2.44.
Programming the number of ringing call
The videointercom can receive 4 different calls
that can be changed as indicated in the
procedure below. The default programming
values and the call sequence are shown in table
2.8. All programming operations must be carried
out with the handset in idle position.
Keep pressed the button "
" for more than 4
seconds; the yellow LED turns ON and you
hear the ring tone that was programmed for
calls from external door station.
a - press the button “
” repeatedly to select
the ring tone.
b - press the button “
” to confirm and go on
to select the number of rings.
c - press the button “
” as many times as the
desired number of rings (once = 1 ring; 4 times
= 4 rings).
d - press the button “
” to confirm and go on
to program the ring tone for intercom calls.
If you want to change the other two tone rings
(call from other user or floor call), you must
repeat steps a-b-c-d.
Pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
Adjusting the volume
With the handset in idle position, you can adjust
4 volume levels for all ring tones, as indicated
below:
press the button “
” for 4 seconds; the yellow
LED turns ON and you hear the external door
station ring tone;
hold the button “
” pressed and release it
when you hear the desired volume;
pick up and close the handset for exit the
programming mode; yellow LED turns-OFF.
The volume levels are stored and will be used for
the next calls.
More programming operations for
specific functions
How to program secondary user
addresses
(additional programming operation that
does not depend on the programming
operations of user and internal station
addresses)
The following programming operation allows
you to save 4 additional user addresses on
the same videointercom (i.e.: exchanger
function, videointercom installed in common
area with multiple users, etc.).
N.B.: videointercom must be programmed
also with the internal common address as
specified in the following.
To make the programming it is necessary:
enter the programming mode following
the instructions described in “Enter the
programming mode”;
keep pressed the button “
” for more
than 4 seconds; yellow LED starts flashing;
again keep pressed the button “
” for
more than 4 sec.; yellow LED starts quickly
flashing;
enter the 3 digit of the 1st user secondary
address (codes from 1 to 200) following
the procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm the present
address and move to the 2nd user ad-
dress; an acknowledge tone will be heard;
enter the 3 digit of the 2nd secondary
user address and confirm by pressing
button
;
proceed entering the 3rd and 4th second-
ary user addresses consumer (if neces-
sary) or to press twice the “
” to pass to
the insertion of the common internal ad-
dress;
enter the 3 digit that compose the common
internal address to the 4 new user
addresses (codes from 000 to 007)
following the procedure of the paragraph
“Entering codes or addresses”.
Note: the internal common address has to
be unique and different from you address
him inside eventually programmed on other
videointercoms and/or intercoms that has the
same user address;
to press “
” to confirm and to return of
choice of programming; an acknowledge tone
will be heard and the yellow LED lights-ON
continuously;
pick up the handset for exit the programming
mode.
Note: If you want to make intercom calls, you
must program the call buttons with the codes of
the users you want to call.
Example
How to program three videointercoms with user
addresses 101, 102 and 103; from which user
103 should receive also calls addressed to user
101 and 102; user 101 and 102 should receive
only calls addressed to them.
- User 101 must be programmed only with user
address 101 and internal address 000.
- User 102 must be programmed only with user
address 102 and internal address 000.
- User 103 must be programmed with user ad-
dress 103, internal address 000, 1
st
secondary
address 101, 2
nd
secondary address 102, in-
ternal common address 001 being the internal
address of videointercoms 101 and 102 al-
ready programmed to 000.
System programming
The following programming allows you to
personalise the operation mode of button “1”
used to deactivate the ring tones and the GC-
GE terminals and send the floor call to the
systems with the same user address (internal
stations in parallel). See table 2.9.
To make the programming it is necessary:
enter the programming mode following the
instructions described in “Enter the
programming mode”;
keep pressed the button “
” for more than 4
seconds; yellow LED starts flashing;
a - keep pressed the button “
” for more than
4 seconds; yellow LED starts quickly flashing;
b - press the button “1” once to enable
operating mode 0 (you hear a sharp tone);
within 2 seconds press the button “1” again to
disable operating mode 0 (you hear a low
tone);
INTERNAL STATIONS
Table 2 - System programming codes
Default
To enable
To disable
Operating modes
value
press 1 time
press 2 times
button "1"
button "1"
mode 0
send floor call to other internal stations in parallel (1)
disabled
enabled
disabled
mode 1
button “1” deactivates all ring tones (2)
disabled
enabled
disabled
mode 2
button “1” deactivates all ring tones and button tones (2)
disabled
enabled
disabled
mode 3
button “1” does not deactivate ring tones and button tones (2)
disabled
enabled
disabled
mode 4
reserved; disabled
disabled
-
disabled
mode 5
the GC-GE terminals are activated upon call from external door station (3)
disabled
enabled
disabled
mode 6
the GC-GE terminals are activated upon intercom call (3)
disabled
enabled
disabled
mode 7
reserved; disabled
disabled
-
disabled
(1) From the internal station connected to the floor call button (terminal A1) and with operating mode 0 enabled, the floor call is also sent to the
other apparatuses in parallel.
(2) If modes 1, 2 and 3 are disabled, press the button “1” for 4 seconds , without a conversation in progress, to deactivate the external and
videointercom ring tones. To reactivate the ring tones, press the button “1” again for 4 seconds; you hear the confirmation tone.
(3) If modes 5 and 6 are disabled, the GC and GE terminals are activated to send the calls.
