2.
47
(MT13 - En 2015)
2
- press button “
” 9 times to enter digit 9 and
press the button “
”; you will hear a tone;
- press button “
” 6 times to enter digit 6 and
press the button “
”; you will hear a tone.
Programming of the user address, internal
address and user secondary address
- User address – this code allows you to
receive an external call, have a conversation
and open the door at the calling external
station.
To program the user address it is necessary
to:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
keep pressed the button
for more than 4
seconds; the programming tone will be heard;
enter the 3 digit of the user address (codes
from 001 to 200) following the procedure
reported on the paragraph “Entering codes
or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
proceed with another programming phase
or exit the programming phase by hanging
up the handset.
- Internal address – these codes are used to
identify the intercoms installed in the
apartment (max.7). In case of one intercom
only, the internal code must be 000 (default
value); if other intercoms are present (max.
other 6) you must assign to them the codes
001, 002, 003 etc. Programming these
addresses all the intercoms will ring-UP when
receiving an external, intercommunicating or
floor (local) call (if programmed) but they may
be called individually within the same
apartment.
Each time the user address programming
procedure is carried out, the internal address
is automatically set to 000. Therefore, run
such a procedure only when the intercom
must be assigned another and different
internal address.
To program the internal address it is
necessary to:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
keep pressed the button
for more than 4
seconds; the programming tone will be heard;
again keep pressed the button
for more
than 4 seconds; the programming tone will
be heard;
enter the 3 digit of the internal address
(codes from 000 to 007) following the
procedure reported on the paragraph
“Entering codes or addresses”;
press the button
to confirm; the acknowl-
edge tone will be heard;
proceed with another programming phase
or exit the programming phase by hanging
up the handset.
INTERNAL STATIONS
PROGRAMMING
The intercom must be suitably programmed for
operation.
Two programming modes are available:
-automatic (quick programming of user code
acting from external station);
-manual (programming of all intercom
functions)
The following programming is possible:
- user address;
- internal address;
- code to assign to buttons “
” and “
” to
make intercom calls or for special services;
- selection of the call timing and call melody
for 4 different call melodies (see table 2.11).
- address to be assigned to terminal A1 to
transfer the floor call to other internal stations.
- secondary address.
Attention: it is mandatory to program the
equipment only with the user code (address) all
other programming are optional.
Factory setting
- User address
= 100
- Internal address = 000
- Buttons “
” and “
” = no codes are stored
to the buttons
- Duration and type of ringer (see table
2.11)
- Terminal A1 address = 255 (see table
2.12)
Enter the programming phase
Hold the button
pressed for more than 4
seconds and, after a warning beep, pick up
the handset; the programming tone will be
emitted.
Release the button
.
Attention. If for 2 minutes no keys are pressed,
system switches back to the operating mode.
Exit the programming phase
You can exit the programming phase at any
time by replacing the handset; the acknowledge
tone will be heard.
Table 2.11. Factory setting for calls
Melody
Calls
Type
Duration
from door station
Din-Don
intercommunicating
Dring 1
from other users
Dring 2
floor (local)
Dring 3
4 rings
Automatic programming
You can use the automatic programming mode
to save the intercom address from the external
station. To enter the automatic programming
mode you must:
enter the programming mode following
the instructions described in “Enter the
programming phase”;
make a call from an external station within
2 minutes. In case of installations with digital
push-button keyboard TD2100, key in the
number you want to assign to the intercom
and press “
”. In case of installations with
digital encoder CD2131÷CD2138 press the
button you want to assign to the user on the
push-button keyboard. When the call is
received, the intercom is programmed
automatically, you hear the call tone in the
handset. Close and pick up the handset to
start a conversation with the external door
station and check the correct operation of the
system; programming mode is signalled on
the external door station by the acknowledge
tone if accepted or a dissuasion tone if
rejected;
repeat programming phases for all the
intercoms connected to the system.
Manual programming
The manual programming mode allows you to
enter the user address, assign: the internal
addresses, the secondary addresses, the
addresses of the buttons "
" and "
", the
address of the terminal A1 and the duration, the
volume and the type of melody.
Entering codes or addresses
Press button "
", ""
" and "
" to enter
addresses or codes.
: Press this button to increase the value
you want to enter. Press the button for a
number of times equal to the digit you want
to enter (digit 1 = 1 time; digit 9 = 9 times;
digit 0 = 10 times).
: Press this button to confirm the digit just
dialled and to proceed to enter next digit
in the following order: hundreds, tens, units.
: Press this button to confirm address or
code programming or go to the next
programming step.
- Codes and/or addresses must have three
digits (hundreds, tens, units); codes and/or
addresses with tens and units or units only
must be completed by adding zeros. For
example, address 96 will become 096 and
address 5 will become 005.
- Digits must be entered individually (beginning
from the hundred), by pressing the button
“
” for a number of times “n”, where “n” is the
value of the digit you want to enter. Store the
digit pressing the button "
"; a tone will
confirm the acquisition of the 1
st
digit.
- Follow the same procedure to store the 2nd
and 3rd digit.
For example, to enter code 096 you must:
- press button “
” 10 times to enter digit 0
and press the button “
”; you will hear a tone;
1 ring
