2.
36
(MT13 - En 2015)
INTERNAL STATIONS
press the button
to confirm; an acknowl-
edge tone will be heard;
proceed with another programming or exit the
programming phase by hanging up the hand-
set.
Resetting the default values
To reset the videointercom default values and
delete all the change made during programming
you must:
enter the programming mode following the
instructions described in “Enter the
programming phase”;
enter the 3 digit 123 following the procedure
reported on the paragraph “Entering codes
or addresses”; a tone indicates that the default
values have been restored;
exit the programming phase by hanging up the
handset.
Choosing the melody for incoming calls
The videointercom can receive 4 different calls
whose melodies can be changed as indicated in
the procedure below. The default melodies and
the call timing are shown in table 2.7.
All programming operations must be carried
out with the handset on hook.
Call from external door station
Keep pressed the button "
" for more than 4
seconds; you hear the melodies that was pro-
grammed for calls from external door station.
Press the button "
" repeatedly to select the
desired melody.
Press the button
to confirm; an acknowl-
edge tone will be heard.
Intercommunicating call
Keep pressed the button "
" for more than 4
seconds; you hear the melody of calls from
external door station.
Keep pressed the button "
" for more than 4
seconds; you hear the melody that was pro-
grammed for intercommunicating calls.
Press the button "
" repeatedly to select the
desired melody.
Press the button
to confirm; an acknowl-
edge tone will be heard.
Call from other user
Keep pressed the button "
" for more than 4
seconds; you hear the melody of calls from
external door station.
Keep pressed the button "
" for more than 4
seconds; you hear the melody of intercommu-
nicating calls.
Keep pressed the button "
" for more than 4
seconds; you hear the melody that was pro-
grammed for calls from other user.
Press the button "
" repeatedly to select
the desired melody.
Press the button
to confirm; an ac-
knowledge tone will be heard.
Floor (local) call
Keep pressed the button "
" for more
than 4 seconds; you hear the melody of
calls from external door station.
Keep pressed the button "
" for more
than 4 seconds; you hear the melody of
intercommunicating calls.
Keep pressed the button "1" for more than
4 seconds; you hear the melody that was
programmed for floor call.
Press the button "
" repeatedly to select
the desired melody.
Press the button
to confirm; the ac-
knowledge tone will be heard.
Timing of ringers
By default, all the videointercom calls last for
4 rings, with the only exception of the floor call
consisting of only one ring that cannot be
changed. The number of rings can be varied
by leaving the handset on hook and
proceeding as follows:
Keep pressed the button "
" for more
than 4 seconds; you hear the melody of
calls from external door station.
Press the button “
” for 4 seconds, it will
be possible to listen to a number of beeps
corresponding to the rings programmed.
Repeatedly press the “
” button to select
the desired number of rings. Each pres-
sure increases the ringing time by one ring.
After 8 rings it again starts from 1.
Press the button
to confirm; an ac-
knowledge tone will be heard.
Adjusting the volume of the ring tone
With the handset on hook, you can adjust 5
volume levels for all ringing tones, as indicated
below:
Keep pressed the button "
" for more
than 4 seconds; you hear the melody of
calls from external door station.
Press the button “1” for 4 seconds, again it
will be possible to listen to the melody of
call from external station.
Press several times the “
” button. Each
pressure increases the volume level of the
ringer. When the maximum level is reached
the device is reset to the minimum.
Press the button
to confirm; an ac-
knowledge tone will be heard.
OPERATION
Call from external station.
When a call is made from the external station,
the videointercom turns ON, generates the
calling melody and stays ON for about 30
seconds. If the call time has expired and the
videointercom has turned OFF, press the button
"
" to reconnect with the calling external station.
Pick up the handset to start conversation with
the external station for about 90 seconds and
press button "
" to open the door.
In case of a call to a user with more than one
videointercom in parallel installed in the
apartment, all the videointercom will ring, but
only the videointercom with internal user
address 000 will turn ON. You can answer also
from this videointercom by following the
instructions above. You can answer from the
other videointercom by picking up the handset.
This operation will automatically turn ON this
videointercom and will turn OFF the
videointercom that had been turned ON before.
Press button "
" if you want to get the image
before answering and then pick up the handset.
Press and hold the “
” button for more than 4
seconds to switch ON the possible additional
camera connected to the external door station.
Monitor function and connection with one
or more external stations.
With the system in stand-by and no conversation
in progress, it would be possible to monitor the
external door stations by picking up the handset
and pressing the button
or the button "1"
previously programmed for this function.
If the installation includes more external stations
and button "
" is programmed correctly, you
can monitor the external stations (max. 4) in
sequence by pressing the same button again
and again.
The videointercom will be turned ON for about
30 seconds. The monitoring will be interrupted
in case of request of monitor from another user,
call between users or from an external station.
If you pick up the handset during the monitoring,
you will automatically establish a conversation
with the external station.
If the videointercom will not turn ON when you
press button "
", this means the installation is
busy and you will have to wait until it becomes
free again.
Making or receiving a call from another
user.
When the installation is in stand-by, you can
make a call to another user. You must have
stored the address of the desired user’s in the
button "1".
To make the call, pick up the handset, wait for
the free tone and press button "1". You will hear
the call tone and the videointercom of the called
user will ring (without turning ON) with a melody
different from calls from external stations or
intercom calls from the same apartment. If the
called user answers within 30 seconds, a 90-
second conversation starts, otherwise the
system goes back to free.
Table 2.7.
Factory setting for calls
Melody
Calls
Timing
Type
from door station
1
Din-Don
intercommunicating
4
Dring 1
from other users
4
Dring 2
floor (local)
1
Dring 3
