![background image](http://html2.mh-extra.com/html/faac/a1000/a1000_user-manual_3115220038.webp)
A1000
38
532210 04 - Rev.A
39
2
6
12
Nm
Tr
ansla
tion of the original instruc
tions
ENGLISH
RH single leaf
Pulley centre dis-
tance (I)
Belt length
f
1000
2140
17
1080
2300
19
1160
2460
20
1240
2620
22
1320
2780
23
1400
2940
24
1480
3100
26
1560
3260
27
1640
3420
29
1720
3580
30
1800
3740
31
1880
3900
33
1960
4060
34
2040
4220
35
2120
4380
37
2200
4540
38
2280
4700
40
2360
4860
41
2440
5020
42
2520
5180
44
2600
5340
45
2680
5500
47
2760
5660
48
2840
5820
49
Double leaf
Pulleys centre
distance (I)
Belt
length
f
1250
2640
22
1320
2780
23
1390
2920
24
1460
3060
25
1530
3200
27
1600
3340
28
1670
3480
29
1740
3620
30
1810
3760
31
1880
3900
33
1950
4040
34
2020
4180
35
2090
4320
36
2160
4460
38
2230
4600
39
2300
4740
40
2370
4880
41
2440
5020
42
2510
5160
44
2580
5300
45
2650
5440
46
2720
5580
47
2790
5720
49
LH single leaf
Pulleys centre
distance (I)
Belt
length
f
1000
2140
17
1080
2300
19
1160
2460
20
1240
2620
22
1320
2780
23
1400
2940
24
1480
3100
26
1560
3260
27
1640
3420
29
1720
3580
30
1800
3740
31
1880
3900
33
1960
4060
34
2040
4220
35
2120
4380
37
2200
4540
38
2280
4700
40
2360
4860
41
2440
5020
42
2520
5180
44
2600
5340
45
2680
5500
47
2760
5660
48
2840
5820
49
9
A1000 belt tensioning (measurements in mm)
11.2 BELT TENSIONING
1. To tension the belt correctly, proceed as follows.
2. Loosen the nut
39
-
.
3. Adjust the screw and nut
39
-
to tension or slacken the belt.
4. Attach a
1 kg
weight in the centre of the lower section of the belt.
5. Measure the arrow
f
and adjust the screw
39
-
using a hex
spanner until obtaining the measurement specified in the table.
6. After adjustment, tighten the screw
39
-
.
7. Carry out a few cycles and make sure the belt remains in its seat
flush with the pulley on the main motor and on the return pulley.
!
Caution - make sure that the belt remains flush with the pulleys of the
main motor and the return pulley.
8. If the belt is not flush with the pulleys, loosen the fastening screws
of the return pulley bracket
39
-
9. Rotate the return pulley bracket clockwise.
10. Tighten the return pulley bracket fastening screws.
11. Perform a few cycles again and check that the belt remains flush
with the pulley.
!
Close the door and ensure:
- the closing point between the two leaves matches with the centre line
of the support profile.
- complete opening and closing is possible.
In case of deviation, check the position and correct connection of the
belt fittings.
!
When the belt is new tensioning adjustment must be repeated after the
first 100 cycles.
Summary of Contents for A1000
