Everest VX Operator'S Manual Download Page 27 | Manualshive

Page: 27 / 71

background image

Installing Leveling Feet (if not already installed)

Using a pallet jack or forklift, lift the machine to a minimum of 18 inches. As a safety precaution,
block the machine anytime there is a risk of machine weight causing injury. Locate the leveling
feet (found inside the machine). Install leveling feet (provided in the coin bin), hand twist legs
into the four corner holes until they are at desired height (recommended: 3 ½ inches between
ground and the machine). Secure by twisting and tightening the jam nut.

Placing and Leveling the Machine

Analyze the foundation and estimate the correct rough adjustment to the leveling feet. Adjust
the feet and set the machine on the foundation. Use a three (3) foot I-beam level to precisely
level the machine.

Note:

NAMA regulations require 6 inches of clearance under the machine The sides and rear

machine panels are square to the frame so you can use the plumb of the sides and rear for
level. Do not use the front doors as your baseline surface for leveling the machine.

Caution: it is critical that the machine is precisely leveled. This is not only for aesthetics. If the
machine is not level, it will not make or dispense ice correctly.

Image 1: Levelling the machine

26

Vb000122015

«
...
25
26
27
28
29
...
»

Summary of Contents for VX








































































Reviews:

No comments

Related manuals for VX

Brand: Janome Pages: 32

Brand: Jack Pages: 20

Brand: IGEBA Pages: 59

Brand: IGEBA Pages: 48

Brand: Singer Pages: 29

UF-6950 - Panafax - Multifunction

Brand: Panasonic Pages: 126

Brand: Singer Pages: 59

Brand: MD SPORTS Pages: 14

Brand: Singer Pages: 13

Brand: Husqvarna Viking Pages: 48

Brand: Siruba Pages: 10

Contest of Champions

Brand: Marvel Pages: 47

Brand: Ricoh Pages: 84

Brand: JUKI Pages: 59

NC81200 CLASSES

Brand: Carpet Sergers Pages: 30

Brand: Hefter Pages: 71

Brand: Hotpoint Pages: 16

Brand: Hefter Systemform Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands