Eurotherm 637+/D6R KD6R Product Manual Download Page 9 | Manualshive

Page: 9 / 87

background image

Product-manual Model: 637+/D6R KD6R

07-02-09-01-E-V0402.doc

9

Safety precautions

Please observe !

Especially to be complied with:

The class of protecton which is permitted: protective grounding; operation is only permitted when
the protective conductor is connected according to regulations.
The operation of servo drives is not allowed under the sole use of a residual current operated
protective device as protection against indirect touching.
The servo drive may only be used in the rack or in its compact enclousure. Furthermore the
regulator is designed solely for control cabinet operation.
Work on or with the servo drive may only be carried out with insulated tools.
Installation work may only be done in a deenergized state. When working on the drive, do not only
block the Aktiv-input but separate the complete drive from the mains.
CAUTION - risk of electrical shock, wait 3 minutes after switching off, for discharging the
capacitors.
Screws sealed with varnish fulfill an important protection function and may not be moved or
removed.
It is prohibited to penetrate the inside of the unit with objects of any kind.
Protect the unit from falling parts (pieces of wire, fley, metal parts, etc.) during installation or other
work in the control cabinet. Metal parts can lead to a short in the servo drive.
Before putting into operation, remove additional covers so that the unit does not overheat. With
measurements at the servo drive it is absolutely necessary to observe the potential separation!

Stop !

Eurotherm Drives Limited is not liable for damages whith occur by not following the instructions
or the applicable regulations !!

«
...
7
8
9
10
11
...
»

Summary of Contents for 637+/D6R KD6R
























































































Reviews:

No comments

Related manuals for 637+/D6R KD6R

MASTERFLEX L/S 7523-40

Brand: Cole Parmer Pages: 23

SmartPilot X-10

Brand: Raymarine Pages: 12

Brand: Advanced Motion Controls Pages: 59

Brand: Panasonic Pages: 48

Brand: Panasonic Pages: 84

Brand: UNI Geräte Pages: 14

DRIVE SHAFT-50PRO

Brand: DoorHan Pages: 18

Brand: Leadshine Pages: 15

Brand: Becker Pages: 28

PowerFlex series

Brand: Rockwell Automation Pages: 294

Bonfiglioli Vectron Agile

Brand: SKS Sweden Pages: 104

POSIDRIVE FDS 5000 series

Brand: Stober Pages: 164

ZAdyn4CA 018 HY

Brand: ZIEHL-ABEGG Pages: 28

Brand: Grundfos Pages: 40

Brand: Melec Pages: 2

Brand: Danfoss Pages: 6

Brand: York Pages: 46

Brand: Omron Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands