Eurotherm 637+/D6R KD6R Product Manual Download Page 5

Page: 5 / 87

Product-manual Model: 637+/D6R KD6R

07-02-09-01-E-V0402.doc

CONTENTS

Page

Operating modes ................................................................................................. 43

3.1

Operating modes and pin functions..................................................................................44

3.2

Configurable pin-functions (depending on the operating mode) .....................................45

3.3

Function diagrams from inputs and outputs.....................................................................46

Mechanical installation ....................................................................................... 47

4.1

Mounting ..........................................................................................................................47

4.2

Control cabinet - mounting ..............................................................................................47

4.3

Cooling.............................................................................................................................47

Electrical installation .......................................................................................... 48

5.1

Safety................................................................................................................................48

5.2

The danger of electric shocks...........................................................................................48

5.3

Danger areas.....................................................................................................................48

5.4

Grounding, safety grounding ...........................................................................................48

5.4.1 Ground connections .........................................................................................................48
5.5

Short-circuit capability and discharge currents................................................................48

5.6

Fuses, contactors, filters...................................................................................................49

5.7

Correction of supply current ............................................................................................50

5.8

Brake resistor ...................................................................................................................51

5.8.1 Selection of the brake resistor..........................................................................................51
5.8.2 Configuration of the brake resistor ..................................................................................52
5.8.3 Additional informations ...................................................................................................53

6 Wiring

instructions ............................................................................................. 54

6.1

General Information .........................................................................................................54

6.2

Control cabling.................................................................................................................54

6.3

Power cabling...................................................................................................................54

6.4

Installation of the rack......................................................................................................54

6.5

Analog setpoint ................................................................................................................54

6.6

Safety rules.......................................................................................................................54

6.7

Electromagnetic compatibility (EMC).............................................................................54

6.7.1 Hints for mounting ...........................................................................................................55
6.7.2 Example for mounting......................................................................................................56
6.7.3 Achieveable specifications and conditions ......................................................................57
7.1

Jumper ..............................................................................................................................58

All jumpers are set to a standard position in production ! ...........................................................58
7.2

Digital communication.....................................................................................................58

Commissioning .................................................................................................... 59

8.1

Preparation .......................................................................................................................59

8.2

Commissioning in steps ...................................................................................................60

Summary of Contents for 637+/D6R KD6R
























































































Search results

Summary of Contents for 637+/D6R KD6R

Reviews:

Eurotherm 637+/D6R KD6R, Product Manual, Page: 5 / 87

Search results

Summary of Contents for 637+/D6R KD6R

Reviews: