Eurotherm 637+/D6R KD6R Product Manual Download Page 10

Page: 10 / 87

Product-manual Model: 637+/D6R KD6R

07-02-09-01-E-V0402.doc

General

1.1

System description

The digital servo drive serves the 4 th generation to regulate the current, speed and position of

AC servo motors,

(standard: with resolver)

All servo controls and functions are realized digitally.

System variants

Rack-version: 637+/D6R....

Compact-version: 637+/K D6R....

Us 24V DC

NEB...

optional

DC-BUS

Ucc

24V DC

637+/D6R

Supply voltage:

1*or 3*230VAC/50..60Hz

3* 400... 460VAC/50..60Hz

637+/K D6R

Us 24VDC

Supply voltage:

1*or 3*230VAC/50..60Hz

3*400...460VAC/50..60Hz

Explanations to rack and power supply modules are documented in separate description.

If required, the returned braking energy can be drawn off into additional external ballast resistors.

The AC-supply voltage is fed directly or via transformer to the associated power supply module.

The devices are designed to be operated on networks which are grounded on
centre point (TN networks) !

Fan

Power supply
plug-in module

NE B

Rack, R6

R6 EMV

XNI

6
5
4
3
2
1

Servodrives

Fan

Servo-

drive

Power supply unit

Summary of Contents for 637+/D6R KD6R
























































































Search results

Summary of Contents for 637+/D6R KD6R

Reviews:

Eurotherm 637+/D6R KD6R, Product Manual, Page: 10 / 87

Search results

Summary of Contents for 637+/D6R KD6R

Reviews: