background image

Product-manual  Model: 637+/D6R KD6R

   

07-02-09-01-E-V0402.doc

17

Range data

1.3.5 Single- and three-phase supply

Due to the line-ripple of DC-Bus, the rate of usable output voltage is derated like follows.
This deration effects the max. reachable speed of the applied motor.

Three-phase-supply:

the unloaded output voltage will be derated to approx. 90%, maximum 85 %

Single-phase: supply:  50 – 60Hz

        only drive 637+ / ..02 up to 06

see following diagram:

Hints for setup:
To avoid unexpected tripping of undervoltage threshold
(EASYRIDER

 Windows - Software), this value should be set to default.

Required motor-terminal-voltage forspecified speed.

Approximation:  (up to 3000RPM)

Ukl = 1,2 * (EMF * n / 1000) + I * (Rph + RL) [V]

Ukl required motorvoltage [V RMS]
EMF Back-EMF of motor  [V RMS] / 1000 RPM
Rph resistance of motor (between terminals) [

]

RL line resistance of motor cable [

]

I

motor-current [A RMS]

Output current [Aeff]

Derating of servo drive output voltage in case of single-phase supply

10 

20 40 60 80 100 

12 

[%] 

 

Output voltage in % of unloaded condition

Summary of Contents for 637+/D6R KD6R
























































































Reviews: