ERM Neoverse N1 Page 198 Technical Reference Manual Download

Page: 198 / 241

Table 4-125 N1 SDP APB system register summary (continued)

Offset

Name

Type

Reset

Width Description

0x0084

SYS_PROC_ID0

0x0X000000

See

4.6.11 SYS_PROC_ID0 Register

on page 4-203

0x0120

SYS_FAN_SPEED

0x00000000

See

4.6.12 SYS_FAN_SPEED Register

on page 4-203

4.6.2

SYS_ID Register

The SYS_ID Register characteristics are:

Purpose

Contains information about the N1 SDP and the bus and image versions inside the IOFPGA.

Usage constraints

The SYS_ID Register is read

‑

only.

Configurations

Available in all N1 board configurations.

Memory offset and full register reset value

See

4.6.1 APB system register summary

on page 4-197

The following table shows the bit assignments.

Table 4-126 SYS_ID Register bit assignments

Bits

Name

Type

Function

[31:28] Rev

Board revision:

0x0

: Rev A board. This is the prototype board

and contains the N1 SoC.

[26:16] HBI

HBI board number in BCD:

0x316

: HBI0316.

[15:12] Build

Build variant of board:

0xF

: All builds.

[11:8]

Arch

IOFPGA bus architecture:

0x4

: AHB.

0x5

: AXI.

[7:0]

FPGA

FPGA build in BCD. The actual value that is
read depends on the FPGA build.

4.6.3

SYS_SW Register

The SYS_SW Register characteristics are:

Purpose

Stores the 8 user DIP switches on the N1 board. A bit set to

0b1

indicates that the switch is ON.

Usage constraints

Bits[29:28] are read

‑

only. Bits[7:0] are read/write.

4 Programmers model

4.6 APB system registers

101489_0000_02_en

reserved.

4-198

Non-Confidential - Beta

Summary of Contents for Neoverse N1

















































































































































































































































Search results

Summary of Contents for Neoverse N1

Reviews:

Related manuals for Neoverse N1

Brands by name

Popular brands

ERM Neoverse N1, Technical Reference Manual

Search results

Summary of Contents for Neoverse N1

Reviews:

Related manuals for Neoverse N1

Brands by name

Popular brands