Ericsson RX1290 Reference Manual Download Page 144

Page: 144 / 176

Menus

C.9.1

Overview ............................................................................................C-20

C.9.2

Transport Stream Alarm Setup Menu.................................................C-21

C.9.3

Video Alarm Setup Menu ...................................................................C-21

C.9.4

Audio 1 Alarm Setup Menu ................................................................C-21

C.9.5

Audio 2 Alarm Setup Menu ................................................................C-22

C.9.6

Audio 3 Alarm Setup Menu ................................................................C-22

C.9.7

Audio 4 Alarm Setup Menu ................................................................C-22

C.9.8

Satellite BER Alarm Setup Menu .......................................................C-22

C.9.9

MER Alarm Setup Menu.....................................................................C-23

C.9.10

C/N Alarm Setup Menu ......................................................................C-23

C.9.11

Temperature Alarm Setup Menu ........................................................C-23

C.10

System Menu (Menu 7) ......................................................................C-23

C.10.1

Setup Menu........................................................................................C-23

C.10.2

Multi-Format Receiver Details Menu ..................................................C-24

C.10.3

System Restart Menu.........................................................................C-25

List of Tables

Table C.1

Main Menu Items..................................................................................C-5

Table C.2

Presets Menu Items .............................................................................C-7

Table C.3

Input Status Menu Items ......................................................................C-7

Table C.4

Input Selection Menu............................................................................C-8

Table C.5

DVB-S2 Input Menu .............................................................................C-8

Table C.6

TTV G.703 Menu..................................................................................C-9

Table C.7

IP Input Menu.......................................................................................C-9

Table C.8

RAS Mode Menu ................................................................................C-12

Table C.9

Common Interface Menu....................................................................C-12

Table C.10

Director 5 Menu..................................................................................C-12

Table C.11

CA Mode Menu ..................................................................................C-13

Table C.12

CA Provide Lock Menu.......................................................................C-13

Table C.13

Service Menu .....................................................................................C-14

Table C.14

Video Menu ........................................................................................C-15

Table C.15

Audio 1 Menu .....................................................................................C-16

Table C.16

Audio 2 Menu .....................................................................................C-16

Table C.17

Audio 3 Menu .....................................................................................C-17

Table C.18

Audio 4 Menu .....................................................................................C-18

Table C.19

Async Data Menu ...............................................................................C-18

Table C.20

High Speed Data Over Ethernet Menu...............................................C-19

Table C.21

VBI Menu ...........................................................................................C-19

Table C.22

PCR PID Menu...................................................................................C-19

Table C.23

Network ID Menu ...............................................................................C-20

Table C.24

Transport Stream Output Menu..........................................................C-20

Table C.25

Output Connector Selector Submenu ................................................C-20

Table C.26

Alarms Menu ......................................................................................C-21

Table C.27

Transport Stream Alarm Setup Menu.................................................C-21

Table C.28

Video Alarm Setup Menu ...................................................................C-21

Table C.29

Audio 1 Alarm Setup Menu ................................................................C-21

Table C.30

Audio 2 Alarm Setup Menu ................................................................C-22

Table C.31

Audio 3 Alarm Setup Menu ................................................................C-22

Table C.32

Audio 4 Alarm Setup Menu ................................................................C-22

Table C.33

Satellite BER Alarm Setup Menu .......................................................C-22

EN/LZT 790 0003/2 R1A

C-2

Summary of Contents for RX1290

















































































































































































Search results

Summary of Contents for RX1290

Reviews:

Brands by name

Popular brands

Ericsson RX1290, Reference Manual

Search results

Summary of Contents for RX1290

Reviews:

Brands by name

Popular brands