manualshive.com logo in svg

Ericsson RX1290, Reference Manual

Share
Download
Ericsson RX1290 Reference Manual Download Page 23

 

 

2 

Installing the Equipment 

Chapter 2 

 

Contents 

2.1

 

Read This First! .................................................................................... 2-3

 

2.1.1

 

Handling ............................................................................................... 2-3

 

2.1.2

 

Installing the Equipment ....................................................................... 2-3

 

2.1.3

 

Lifting .................................................................................................... 2-3

 

2.1.4

 

Site Requirements ................................................................................ 2-3

 

2.1.4.1

 

Power Supplies..................................................................................... 2-3

 

2.1.4.2

 

Environment ......................................................................................... 2-3

 

2.1.4.3

 

Lightning Protection.............................................................................. 2-3

 

2.2

 

Preliminary Checks............................................................................... 2-4

 

2.2.1

 

Mechanical Inspection .......................................................................... 2-4

 

2.2.2

 

Moving the Equipment Safely............................................................... 2-4

 

2.3

 

Installing the Equipment ....................................................................... 2-4

 

2.3.1

 

Fixing .................................................................................................... 2-4

 

2.3.2

 

Ventilation............................................................................................. 2-5

 

2.3.3

 

Openings in the Covers ........................................................................ 2-5

 

2.3.3.1

 

Care in Positioning ............................................................................... 2-5

 

2.3.3.2

 

Protection from Moisture ...................................................................... 2-5

 

2.3.4

 

Installing Cables - Safety...................................................................... 2-6

 

2.4

 

EMC Compliance Statements .............................................................. 2-6

 

2.4.1

 

EN 55022/AS/NZS 3548....................................................................... 2-6

 

2.4.2

 

FCC ...................................................................................................... 2-6

 

2.5

 

AC Supply Operating Voltage and Fusing – Safety Information........... 2-6

 

2.5.1

 

AC Power Supply ................................................................................. 2-6

 

2.5.2

 

AC  Power Supply Cord........................................................................ 2-7

 

2.5.2.1

 

General................................................................................................. 2-7

 

2.5.2.2

 

Wire Colors........................................................................................... 2-7

 

2.5.3

 

Connecting the Equipment to the AC Power Supply ............................ 2-8

 

2.6

 

Protective Earth/Technical Earth .......................................................... 2-8

 

2.7

 

Signal Connections............................................................................... 2-9

 

2.7.1

 

General................................................................................................. 2-9

 

2.7.2

 

ASI/HD-SDI/SD-SDI OUT................................................................... 2-11

 

2.7.3

 

CVBS.................................................................................................. 2-11

 

2.7.4

 

Audio Outputs..................................................................................... 2-11

 

2.7.5

 

SVGA Output (RGB HV)..................................................................... 2-12

 

2.7.6

 

Frame Synchronization....................................................................... 2-13

 

2.7.7

 

Ethernet .............................................................................................. 2-14

 

2.7.8

 

ASI IN ................................................................................................. 2-14

 

EN/LZT 790 0003/2 R1A

 

 

 

 

2-1

 

Summary of Contents for RX1290

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands