manualshive.com logo in svg

Ericsson RX1290, Reference Manual

Share
Download
Ericsson RX1290 Reference Manual Download Page 77

 

 

6 

Options 

Chapter 6 

 

Contents 

6.1

 

Hardware Enabled Options .................................................................. 6-3

 

6.2

 

DVB-S2 Input Cards (RX1290/HWO/DVBS2 and 
RX1290/HWO/DVBS2/IF/CONST) ....................................................... 6-3

 

6.2.1

 

General................................................................................................. 6-3

 

6.2.2

 

Connector Details - L-Band Inputs ....................................................... 6-3

 

6.2.3

 

Connector Details – IF Monitor Input 
(RX1290/HWO/DVBS2/IF/CONST)...................................................... 6-4

 

6.2.4

 

Connector Details – Constellation Output 
(RX1290/HWO/DVBS2/IF/CONST)...................................................... 6-5

 

6.3

 

TTV G.703 DS3 and E3 Input Card (TT1290/HWO/G703)................... 6-5

 

6.4

 

IP Input Card (TT1290/HWO/IP) .......................................................... 6-5

 

6.5

 

100/1000BaseT Dual IP Input – RX1290/HWO/GIGE.......................... 6-7

 

6.5.1.1

 

Mode of Operation when input port is set to Auto ................................ 6-7

 

6.5.1.2

 

Mode of Operation when input port is set to Port 1 or Port 2................ 6-8

 

6.5.1.3

 

Mode of Operation when switching from input Port 2 to Auto............... 6-8

 

6.6

 

Software Enabled Options.................................................................... 6-8

 

6.7

 

High Speed Data Over Ethernet (RX1290/SWO/HSETHER)............... 6-8

 

6.8

 

Dolby Digital Decoder (RX1290/SWO/AC3) ......................................... 6-8

 

6.9

 

RAS Mode 1 and 2 Conditional Access (RX1290/SWO/RAS) ............. 6-8

 

6.10

 

Director Functionality (RX1290/SWO/DIR5)......................................... 6-8

 

6.11

 

MPEG-2 HD 4:2:2 Decode (RX1290/SWO/MPEG-2/HD/422) ............. 6-9

 

6.12

 

MPEG-4 SD Decode (RX1290/SWO/MPEG4/SD) ............................... 6-9

 

6.13

 

MPEG-4 HD, SD MPEG-2, HD 4:2:2 Decode 
(RX1290/SWO/MPEG-4/HD)................................................................ 6-9

 

6.14

 

DVB-S2 QPSK (RX1290/SWO/DVBS2/QPSK) .................................... 6-9

 

6.15

 

DVB-S2 QPSK and 8PSK (RX1290/SWO/DVBS2/8PSK).................... 6-9

 

6.16

 

DVB-S2 Low Symbol Rate (RX1290/SWO/DVBS2/LSym)................... 6-9

 

6.17

 

ProMPEG FEC (RX1290/SWO/IP/PROMPEG).................................... 6-9

 

6.18

 

Four Channel Audio Support (RX1290/SWO/4AUD)............................ 6-9

 

6.19

 

AAC Audio Support (RX1290/SWO/AAC) .......................................... 6-10

 

6.20

 

Down Conversion (RX1290/SWO/DCONV) ....................................... 6-10

 

6.21

 

Common Interface (RX1290/SWO/CI)................................................ 6-10

 

6.22

 

Provider Lock (RX1290/SWO/PROV/LOCK)...................................... 6-10

 

6.23

 

Web Browser Password Protection (RX1290/SWO/PW) ................... 6-10

 

 

EN/LZT 790 0003/2 R1A

  

 

 

 

6-1

 

Summary of Contents for RX1290

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands