manualshive.com logo in svg

Ericsson RX1290, Reference Manual

Share
Download
Ericsson RX1290 Reference Manual Download Page 28

Installing the Equipment 

 

 

2.3.4 

Installing Cables - Safety 

Power supply cables should be routed so that they are not likely to be walked on or 
pinched by items placed upon or against them. Pay particular attention to cables at 
plugs, convenience receptacles, and the point where they exit from the appliance. 

Do not run AC power cables in the same duct as signal leads. Do not move or install 
equipment whilst it is still attached to the mains supply. Ensure safety and ESD 
precautions are observed whilst inter-connecting equipment. 

2.4 

EMC Compliance Statements

1

 

2.4.1 

EN 55022/AS/NZS 3548 

This is a Class A product. In a domestic environment this product may cause radio 
interference in which case the user may be required to take adequate measures. 

2.4.2 

FCC 

This equipment has been tested and found to comply with the limits for a Class A 
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to 
provide reasonable protection against harmful interference when the equipment is 
operated in a commercial environment. 

This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the Reference Guide, may cause harmful 
interference to radio communications. Operation of this equipment in a residential 
area is likely to cause harmful interference in which case the user will be required to 
correct the interference at his/her own expense. 

2.5 

AC Supply Operating Voltage and Fusing – Safety 
Information 

2.5.1 

AC Power Supply 

The equipment operates from an wide-ranging mains power supply (100-240 V AC 
50/60 Hz nominal) and is designed for use in ambient air temperature in the range 
0

°

C to +50

°

C. There are no links etc. to be altered for operation from different 

supply voltages. The full Technical Specification is given in 

Annex B, Technical 

Specification

. 

                                                      

1

 The EMC information was correct at the time of manufacture. The EMC tests were performed with the Technical Earth attached. 

 

EN/LZT 790 0003/2 R1A

 

2-6 

 

 

 

Summary of Contents for RX1290

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands