manualshive.com logo in svg

Ericsson EDACS Data Advantage Series, Installation And Maintenance Manual, Page: 4 / 48

Share
Download
Ericsson EDACS Data Advantage Series Installation And Maintenance Manual Download Page 4

LBI-39190

4

PREFACE

This is one of four manuals for Data Advantage.  It contains instructions for installing and maintaining the Data
Advantage equipment.  Network planning and the boot sequence are also documented in this manual.  Other
relevant documents are:

Data Advantage Technical Description (LBI-39188):

This manual contains a detailed description of the Data Advantage capabilities, interfaces, and hardware.

Data Advantage User's Reference Manual (LBI-39191):

This manual contains information for using the Data Advantage command shell.  This command shell
services the Diagnostic Terminal and Telnet logins.

Data Advantage Configuration Reference Manual (LBI-39189):

This manual contains the information required to configure the Data Advantage.

Internetworking with TCP/IP, Volume I, by Douglas E. Comer:

This is an excellent (but unofficial) source of information about Internet Protocol.

EDACS CommServ Programmers Guide (LBI-38835):

This manual documents the CommServ product.  CommServ provides an application program interface
that simplifies Radio Data Terminal (RDT) programming by providing an RDI Data Link Layer.  It is for
use with MS-DOS (trademark of Microsoft Corporation) and PC-DOS.

Mobile Data Terminal Interface, Hardware and Protocol, Version 1.92

This manual documents the RDI Interface.

If you are unable to resolve a problem or need additional technical assistance, contact Ericsson’s Technical
Assistance Center (TAC) at the number shown on the last page of this manual.

Summary of Contents for EDACS Data Advantage Series

















































Reviews:

No comments