manualshive.com logo in svg

Ericsson EDACS Data Advantage Series, Installation And Maintenance Manual, Page: 3 / 48

Share
Download
Ericsson EDACS Data Advantage Series Installation And Maintenance Manual Download Page 3

LBI-39190

3

RF Control Station Statistics.......................................................................................................................................... 36
System Startup................................................................................................................................................................ 37
Network Connections ..................................................................................................................................................... 39
RF Control Stations........................................................................................................................................................ 40
Radios / RDTs ................................................................................................................................................................ 41
Excessive Error Rate...................................................................................................................................................... 42

ICMP MESSAGES RETURNED BY DATA ADVANTAGE............................................................................................ 43
FORCING A HARD DISK REFORMAT ........................................................................................................................... 43
FUSES ................................................................................................................................................................................. 44

CAP Board Fuse ............................................................................................................................................................ 44
SCSI Fuse....................................................................................................................................................................... 44
VCOM24 Fuses .............................................................................................................................................................. 45

PIN OUT FOR THE DIAGNOSTIC TERMINAL CABLE................................................................................................ 46
PIN OUT FOR DATA INTERFACE CABLE .................................................................................................................... 46
PIN OUT FOR RADIO SHELF HARNESS / DATA INTERFACE................................................................................... 46
PIN OUT FOR THE PROGRAMMING CABLE ............................................................................................................... 47
PIN OUT FOR RADIO SHELF HARNESS / RADIO PROGRAMMING......................................................................... 47

Summary of Contents for EDACS Data Advantage Series

















































Reviews:

No comments