manualshive.com logo in svg

Ericsson EDACS Data Advantage Series, Installation And Maintenance Manual, Page: 18 / 48

Share
Download
Ericsson EDACS Data Advantage Series Installation And Maintenance Manual Download Page 18

LBI-39190

18

MVME147 BOARD SETUP

The Data Advantage equipment must be powered off when removing or inserting processor
boards.

WARNING

There are two types of processor boards installed in the Data Advantage VME chassis:  MVME147 and
VCOM24.  There will be only one  MVME147 board, located in the bottom slot (slot 1).  There will be one or
two VCOM24 boards, beginning at slot 3.  Each of these boards requires the installation of an EPROM set and
the correct jumper settings for normal operation.

Shown below are the jumper settings for the MVME147 board.  The two EPROMs for this board are to be
installed in U22 and U30.  U1 and U15 will not have any EPROMs installed.

U30

U22

U15

U1

J1

J2

J3

J5

J6

J7

J8

J9

F1

Spare Fuse *

Figure 5 - MVME147 Board Jumper Settings, Fuses, and Sockets

*   The Spare Fuse is on the 1992 revision of the board, but not the 1988 revision.  The revision date is generally

on the back near the VME connectors.

Summary of Contents for EDACS Data Advantage Series

















































Reviews:

No comments