Epson Perfection 3200 Photo Service Manual Download Page 34

Page: 34 / 78

EPSON Perfection 3200 Photo

Revision A

Troubleshooting

Figure 3-3. The lamp does not light up.

Figure 3-4. Scanned image is unclear.

Start

Is connector

CN6 on the main

circuit board

connected?

Are connectors

CN1 and CN2 on

the CCD circuit

board connected?

Is fluorescent lamp

inserted securely

into inverter circuit

board?

Is the harness

connected to the

main circuit board

and carriage?

Replace the main

circuit board.

Replace the

carriage.

Reset into inverter

circuit board.

Connect the

connector.

Connect the

connector.

Start

Is the document

platen dirty?

Is the mirror inside

the carriage dirty?

Is the

Sheet White section

dirty or bent?

Is the

CCD sensor circuit

board normal?

Is the scanned

image okay?

Mechanism problem

(replacement required)

Replace the main

circuit board.

Replace the

carriage unit.

Replace the upper

housing.

Clean.

(See 6.1.1 Cleaning.)

* White spots appear in image.

* Vertical stripes appear in image.

Clean.

(See 6.1.1 Cleaning.)

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands