Epson Perfection 3200 Photo Service Manual Download Page 53

Page: 53 / 78

EPSON Perfection 3200 Photo

Revision A

Disassembly and Assembly

DISASSEMBLY AND ASSEMBLY

4.2.11 Power Supply Cable Removal

Release the carriage lock. (See Section 4.2.1.)

Remove the document cover. (See Section 4.2.2.)

Remove the upper cover. (See Section 4.2.3.)

Remove the three screws (CBS, M3x5), and the disconnect the lock-type
connector (CN1) from the power supply circuit board. (See Figure 4-34)

Remove the power supply cable cover. (See Figure 4-34)

Disengage the two hooks, and then remove the power supply cable unit.
(See Figure 4-35)

Figure 4-34. Power Supply Cable Removal (1)

Figure 4-35. Power Supply Cable Removal (2)

When securing the power supply cable unit, secure the
Cover Cover Inlet with the same screws.

Attach the power supply cable cover to the lower housing
with double-sided tape.

Cover Cover Inlet

Power Supply Cable

Cover

CBB Screws (3x12)

Tightening Torque : 6-8kgfcm

Connector

Hooks

Power Supply Cable

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands