Epson Perfection 3200 Photo Service Manual Download Page 45

Page: 45 / 78

EPSON Perfection 3200 Photo

Revision A

Disassembly and Assembly

DISASSEMBLY AND ASSEMBLY

Remove the two screws (CBS, M3x5) and disengage the three hooks, and
then remove the main circuit board shield plate. (See Figure 4-14)

Disconnect the white FFC from the main circuit board. (See Figure 4-15)

Disconnect the white FFC from the ferrite core. (See Figure 4-15)

10. Disconnect the white FFC from the carriage unit. (See Figure 4-16)

Figure 4-14. Carriage Unit Removal (4)

Figure 4-15. Carriage Unit Removal (5)

Figure 4-16. Carriage Unit Removal (6)

The FFCs should be attached to the base frame with
double-sided tape.

CBS Screws (3x5)

Tightening Torque : 8-10kgfcm

Main Circuit Board

Shield Plate

Hooks

FFC

Main Circuit Board

Ferrite Core

FFC Connector

FFC

Carriage Unit

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands