Epson Perfection 3200 Photo Service Manual Download Page 20

Page: 20 / 78

EPSON Perfection 3200 Photo

Revision A

Product Description

Energy Save Mode

1.8 Energy Save Mode

When the scanner switches to energy save mode, the control status is as
shown below.

1.8.1 Mode transitions

Figure 1-8. Mode Transition Diagram

1.8.2 Energy save control

During scanning standby
The following control operation is carried out during scanning standby.

The CCD clock is fixed at LOW level.
This control is carried out after the carriage returns once scanning is
complete.

During energy save mode
The following control operations are carried out during energy save mode.

CCD and AFE clocks are fixed at LOW levels.

12 V power supply stops.

Indicators switch off.

Power ON

Warm - up

Scanning operation

Energy save

mode

·14 minutes pass

in standby

Scanning standby

·Command other than

ESC ! received

·Pushbutton pressed

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands