Epson Perfection 3200 Photo Service Manual Download Page 35

Page: 35 / 78

EPSON Perfection 3200 Photo

Revision A

Troubleshooting

Figure 3-5. Host does not recognize scanner even when

power is turned on.

Figure 3-6. Option TPU does not operate.

Start

Does host support

USB or IEEE 1394?

Is accessory twain

driver for scanner

installed correctly?

Is the USB or IEEE

1394 cable normal?

Replace the main

circuit board.

Replace host.

Install (or re-install) the
GT-9700F twain driver.

Replace the cable

* Srart Windows and check
“My Computer” — “Properties” — “Device Manager”.
Is USB enabled?

Start

Is the TPU cable

at the back of the

scanner connected

correctly?

Is connector CN9 on

the main circuit

board connected?

Is the option main

circuit board

normal?

Replace the scanner

main circuit board.

Replace the option

main circuit board.

Connect the

connector

Connect the cable.

* +24 V system: lamp, monitor
+5 V system: sensor, logic circuit

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands