Epson Perfection 3200 Photo Service Manual Download Page 33

Page: 33 / 78

EPSON Perfection 3200 Photo

Revision A

Troubleshooting

Figure 3-1. Scanner does not operate the initializarion.

Figure 3-2. Carriage Unit does not operate.

Start

Are all connectors

connected

normally?

Is the power fuse

okay?

Does the CR motor

operate normally?

Does the lamp

illuminate?

Connect correctly.

Replace the power

supply circuit board.

Replace the CR

motor.

Replace the power

supply circuit board.

Replace the main

circuit board.

Start

Is the carriage lock

released?

Is the upper housing

installed correctly?

Is connector CN6

on the main circuit

board connected?

Is the harness

connected to the

main circuit board

and carriage?

Is the carriage

mechanism normal?

Does the CR motor

operate normally?

Replace the CR

motor.

Connect the

harness

Connect the

connector.

Install normally.

Release the

carriage lock.

Replace the main

circuit board.

Reassemble.

Replace applicable

part.

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands