Epson Perfection 3200 Photo Service Manual Download Page 51

Page: 51 / 78

EPSON Perfection 3200 Photo

Revision A

Disassembly and Assembly

DISASSEMBLY AND ASSEMBLY

Figure 4-29. SUB_A Circuit Board Removal (2)

4.2.10 Power Supply Circuit Board Removal

Release the carriage lock. (See Section 4.2.1.)

Remove the document cover. (See Section 4.2.2.)

Remove the upper cover. (See Section 4.2.3.)

Remove the two screws (CBS, M3x5). (See Figure 4-30)

Disengage the two hooks at the side of the scanner, and then remove the
power supply circuit board unit. (See Figure 4-31)

Disconnect the lock-type AC adapter connector (CN1), SUB_A circuit
board connector (CN102) and main circuit board connector (CN101). (See
Figure 4-32)

Remove the five screws (CBS, M3x5), and then remove the power supply
circuit board from the power supply circuit board cover. (See Figure 4-33)

Remove the power supply circuit board cover sheet from the power supply
circuit board cover.

Figure 4-30. Power Supply Circuit Board Removal (1)

CBS Screws (3x5)

Tightening Torque : 8-10kgfcm

Hooks

Lift up front

CBS Screws (3x5)

Tightening Torque : 8-10kgfcm

Power Supply

Circuit Board Unit

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands