Epson Perfection 3200 Photo Service Manual Download Page 42

Page: 42 / 78

EPSON Perfection 3200 Photo

Revision A

Disassembly and Assembly

DISASSEMBLY AND ASSEMBLY

4.2.3 Upper Cover Removal

Release the carriage lock. (See Section 4.2.1.)

Remove the document cover. (See Section 4.2.2.)

Remove the two screws (CBP, M3x8) at the back of the scanner. (See
Figure 4-6.)

While lifting up the upper cover and pulling it forward, disengage the three
hooks at the front of the upper cover, and then remove the upper cover.

Disconnect the connector (CN1) from the SUB_A circuit board. (See Figure
4-8)

Figure 4-6. Upper Cover Removal (1) - Screw Positions

Figure 4-7. Document Cover Removal (2)

Figure 4-8. Upper Cover Removal (3)

C A U T I O N

When removing the upper cover, make sure that the hooks
are properly disengaged so that the tabs do not get broken.

CBP Screws (3x8)

Tightening Torque : 8-10kgfcm

Hooks

Connector

Summary of Contents for Perfection 3200 Photo















































































Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands

Epson Perfection 3200 Photo, Service Manual

Search results

Summary of Contents for Perfection 3200 Photo

Reviews:

Related manuals for Perfection 3200 Photo

Brands by name

Popular brands